(Argh!) 2.6.11.1 w/ 0.3.7 = wifi0: hfa384x_cmd: entry still in list?

Jason Straight jason at jeetkunedomaster.net
Wed Mar 9 20:45:07 EST 2005


Well, if I have my prism card in when pcmcia starts my card will work, at 
least until I eject/insert it again. Then it will fail. The io addy is still 
the same when it's working.

It seems to be that as long as it loads before ath_pci it's ok? But if I 
ifconfig all the devs down, and remove all the modules and restart pcmcia 
when I re-insert the prism card it still fails. I'm wondering if this isn't 
more of a problem with madwifi drivers.


On Wednesday 09 March 2005 19:30, Jason Straight wrote:
> Below is a bunch of crap :) hopefully containing the right information so
> someone can point me to the reason why I can't get my zcom 325-HP working.
>
>
> Here's the full dmesg:
>
> hostap_crypt: registered algorithm 'NULL'
> hostap_cs: 0.3.7 - 2005-02-12 (Jouni Malinen <jkmaline at cc.hut.fi>)
> hostap_cs: setting Vcc=33 (constant)
> hostap_cs: CS_EVENT_CARD_INSERTION
> hostap_cs: setting Vcc=50 (from config)
> Checking CFTABLE_ENTRY 0x01 (default 0x01)
> IO window settings: cfg->io.nwin=1 dflt.io.nwin=1
> io->flags = 0x0046, io.base=0x0000, len=64
> hostap_cs: Registered netdevice wifi0
> hostap_cs: index 0x01: Vcc 5.0, irq 16, io 0x0100-0x013f
> prism2_hw_init: initialized in 195 ms
> wifi0: hfa384x_cmd: entry still in list? (entry=ea665e80, type=0, res=0)
> wifi0: hfa384x_cmd: command was not completed (res=0, entry=ea665e80,
> type=0, cmd=0x0001, param0=0x0000, EVSTAT=8000 INTEN=0010)
> wifi0: MAC port 0 enabling failed
> wifi0: could not enable MAC port
> wifi0: hfa384x_cmd: entry still in list? (entry=c957d7c0, type=0, res=0)
> wifi0: hfa384x_cmd: command was not completed (res=0, entry=c957d7c0,
> type=0, cmd=0x0021, param0=0xfd0b, EVSTAT=8000 INTEN=0010)
> wifi0: hfa384x_get_rid: CMDCODE_ACCESS failed (res=-110, rid=fd0b, len=8)
> Could not get RID for component NIC
> hostap_cs: Initialization failed
> prism2_config() failed
> r8169: eth0: PHY reset until link up
> wifi0: hfa384x_cmd: entry still in list? (entry=ea665e80, type=0, res=0)
> wifi0: hfa384x_cmd: command was not completed (res=0, entry=ea665e80,
> type=0, cmd=0x0002, param0=0x0000, EVSTAT=8000 INTEN=0000)
> hostap_cs: Shutdown failed
>
>
> iwconfig shows:
>
> ath0      IEEE 802.11g  ESSID:"{{}}"  Nickname:"jkd.jeetkunedomaster.net"
>           Mode:Managed  Frequency:2.412 GHz  Access Point:
> 00:04:5A:0E:3C:F6 Bit Rate:11 Mb/s   Tx-Power:50 dBm   Sensitivity=0/3
>           Retry:off   RTS thr:off   Fragment thr:off
>           Encryption key:off
>           Power Management:off
>           Link Quality=60/94  Signal level=-35 dBm  Noise level=-95 dBm
>           Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
>           Tx excessive retries:24  Invalid misc:24   Missed beacon:0
>
> wifi0     no wireless extensions.
>
>
>
> Worth noting my machine has a wireless minipci dev running with madwifi on
> ath0.
>
> lspci:
>
> 00:00.0 Host bridge: VIA Technologies, Inc. VT8385 [K8T800 AGP] Host Bridge
> (rev 01)
> 00:01.0 PCI bridge: VIA Technologies, Inc. VT8237 PCI bridge [K8T800 South]
> 00:05.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg
> NIC (rev 01)
> 00:06.0 FireWire (IEEE 1394): Texas Instruments TSB43AB21 IEEE-1394a-2000
> Controller (PHY/Link)
> 00:08.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8169
> Gigabit Ethernet (rev 10)
> 00:0c.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller (rev
> 01) 00:0e.0 Unknown mass storage controller: Winbond Electronics Corp:
> Unknown device 8481 (rev 01)
> 00:0e.1 Unknown mass storage controller: Winbond Electronics Corp: Unknown
> device 8482 (rev 01)
> 00:10.0 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
> Controller (rev 80)
> 00:10.1 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
> Controller (rev 80)
> 00:10.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
> Controller (rev 80)
> 00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82)
> 00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
> 00:11.1 IDE interface: VIA Technologies, Inc.
> VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06)
> 00:11.5 Multimedia audio controller: VIA Technologies, Inc.
> VT8233/A/8235/8237 AC97 Audio Controller (rev 50)
> 00:11.6 Communication controller: VIA Technologies, Inc. AC'97 Modem
> Controller (rev 80)
> 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> HyperTransport Technology Configuration
> 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> Address Map
> 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> DRAM Controller
> 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron]
> Miscellaneous Control
> 01:00.0 VGA compatible controller: ATI Technologies Inc RV350 [Mobility
> Radeon 9600 M10]
>
>
> and /proc/interrupts
>
> [root at jkd hostap-driver-0.3.7]# cat /proc/interrupts
>            CPU0
>   0:   71822068    IO-APIC-edge  timer
>   1:      44579    IO-APIC-edge  i8042
>   7:          2    IO-APIC-edge  parport0
>  10:     179318   IO-APIC-level  acpi
>  12:     178411    IO-APIC-edge  i8042
>  14:     289309    IO-APIC-edge  ide0
>  15:     646049    IO-APIC-edge  ide1
>  16:    2099545   IO-APIC-level  yenta, ath0, 0.0
>  17:          3   IO-APIC-level  ohci1394
>  19:          6   IO-APIC-level  eth0
>  21:     442114   IO-APIC-level  uhci_hcd, uhci_hcd, uhci_hcd, ehci_hcd
>  22:    3248927   IO-APIC-level  VIA8233
> NMI:          0
> LOC:   71817707
> ERR:          0
> MIS:          0
>
> Thanks, this really bugs me since I don't really know what would cause this
> error. I know 2.6.11.1 has some new acpi IRQ handling but I don't know if
> that would cause this error or not.

-- 
http://www.skycon.net/
AIM: JasonRStraight
ICQ: 1796276



More information about the HostAP mailing list