Failing LEAP authentication (Was:ioctl[IPW2100_IOCTL_WPA_SUPPLICA NT]: Operation not supported)

Richard.Griffiths at windriver.com Richard.Griffiths at windriver.com
Wed Jan 26 18:54:53 EST 2005


> The error message is probably caused by the ipw2100 driver not having 
> WPA support compiled in. Maybe the ipw2100 is in the initrd image and 
> the system is loading that one instead of the one you compiled. Try 
> using the ./unload and ./load scripts in the ipw2100 driver source. 
> --  
> Pedro Ramalhais <ramalhais at serrado.net>
> 
Good tip. My problem was I have ipw2100 configured in my current kernel
and those settings were overriding the external module I'm building. The
operation not supported messages are gone.  
But, I'm still not authenticating.  Here's the new debug output:

Initializing interface 'eth1' conf '/etc/wpa_supplicant.conf' driver
'ipw2100'
Configuration file '/etc/wpa_supplicant.conf' ->
'/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
eapol_version=1
ap_scan=1
Line: 5 - start of a new network block
ssid - hexdump_ascii(len=7):
     74 73 75 6e 61 6d 69                              tsunami
key_mgmt: 0x8
eap methods - hexdump(len=2): 11 00
identity - hexdump_ascii(len=8):
     72 67 72 69 66 66 69 74                           rgriffit
password - hexdump_ascii(len=8):
     61 62 72 61 78 20 61 73                           abrax as
Priority group 0
   id=0 ssid='tsunami'
Initializing interface (2) 'eth1'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Own MAC address: 00:0c:f1:56:83:53
wpa_driver_ipw2100_set_wpa: enabled=1
wpa_driver_ipw2100_set_key: alg=none key_idx=0 set_tx=0 seq_len=0
key_len=0
wpa_driver_ipw2100_set_key: alg=none key_idx=1 set_tx=0 seq_len=0
key_len=0
wpa_driver_ipw2100_set_key: alg=none key_idx=2 set_tx=0 seq_len=0
key_len=0
wpa_driver_ipw2100_set_key: alg=none key_idx=3 set_tx=0 seq_len=0
key_len=0
wpa_driver_ipw2100_set_countermeasures: enabled=0
wpa_driver_ipw2100_set_drop_unencrypted: enabled=1
Setting scan request: 0 sec 100000 usec
Starting AP scan (broadcast SSID)
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
Scan timeout - try to get results
Received 869 bytes of scan results (4 BSSes)
Scan results: 4
Selecting BSS from priority group 0
0: 00:0f:66:ed:f9:8c ssid='<hidden>' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
1: 00:40:96:58:53:b9 ssid='<hidden>' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
2: 00:40:96:58:53:b9 ssid='tsunami' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
3: 00:09:5b:ef:69:a2 ssid='basic' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
   selected non-WPA AP 00:40:96:58:53:b9 ssid='tsunami'
Trying to associate with 00:40:96:58:53:b9 (SSID='tsunami' freq=0 MHz)
Cancelling scan request
Automatic auth_alg selection: 0x4
wpa_driver_ipw2100_set_auth_alg: auth_alg=0x4
No keys have been configured - skip key clearing
wpa_driver_ipw2100_set_drop_unencrypted: enabled=1
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b1a len=20
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
Authentication with 00:00:00:00:00:00 timed out.
Added BSSID 00:00:00:00:00:00 into blacklist
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
Scan timeout - try to get results
Received 871 bytes of scan results (4 BSSes)
Scan results: 4
Selecting BSS from priority group 0
0: 00:0f:66:ed:f9:8c ssid='<hidden>' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
1: 00:40:96:58:53:b9 ssid='<hidden>' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
2: 00:40:96:58:53:b9 ssid='tsunami' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
3: 00:09:5b:ef:69:a2 ssid='basic' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
   selected non-WPA AP 00:40:96:58:53:b9 ssid='tsunami'
Trying to associate with 00:40:96:58:53:b9 (SSID='tsunami' freq=0 MHz)
Cancelling scan request
Automatic auth_alg selection: 0x4
wpa_driver_ipw2100_set_auth_alg: auth_alg=0x4
No keys have been configured - skip key clearing
wpa_driver_ipw2100_set_drop_unencrypted: enabled=1
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8b1a len=20
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
Signal 2 received - terminating
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_ipw2100_set_wpa: enabled=0
wpa_driver_ipw2100_set_drop_unencrypted: enabled=0
wpa_driver_ipw2100_set_countermeasures: enabled=0
Removed BSSID 00:00:00:00:00:00 from blacklist (clear)

-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/ms-tnef
Size: 4119 bytes
Desc: not available
Url : http://lists.shmoo.com/pipermail/hostap/attachments/20050126/9dc32d09/attachment.bin 


More information about the HostAP mailing list