Ndiswrapper +wpa_supplicant

Andrew Duane andrew at duaneville.com
Sun Nov 21 08:13:17 EST 2004


Oh just reread and missed some information.

My ndis driver is bcmwl5 and the wireless card is the linksys wmp54g,
although ndis works okay when I turn off wpa encryption.

Also here is what is returned from iwlist wlan0 scan:

wlan0     Scan completed :
          Cell 01 - Address: 00:0C:41:9D:F4:4A
                    ESSID:"Foundation"
                    Protocol:IEEE 802.11b
                    Mode:Managed
                    Frequency:2.452GHz
                    Quality:0/100  Signal level:-54 dBm  Noise level:-256
dBm
                    Encryption key:on
                    Bit Rate:1Mb/s
                    Bit Rate:2Mb/s
                    Bit Rate:5.5Mb/s
                    Bit Rate:11Mb/s
                    Bit Rate:18Mb/s
                    Bit Rate:24Mb/s
                    Bit Rate:36Mb/s
                    Bit Rate:54Mb/s
                    Bit Rate:6Mb/s
                    Bit Rate:9Mb/s
                    Bit Rate:12Mb/s
                    Bit Rate:48Mb/s
                    Extra:bcn_int=100
                    Extra:atim=0
 
Extra:wpa_ie=dd160050f20101000050f20201000050f20201000050f202

A bit odd it says that the protocol is 802.11b as I have it set to only
accept 802.11g???

-----Original Message-----
From: hostap-bounces+andrew=duaneville.com at shmoo.com
[mailto:hostap-bounces+andrew=duaneville.com at shmoo.com] On Behalf Of Andrew
Duane
Sent: 21 November 2004 13:06
To: 'Jouni Malinen'
Cc: hostap at shmoo.com
Subject: RE: Ndiswrapper +wpa_supplicant

Thanks for your reply.

I'm running version 0.11 of ndiswrapper and 0.2.5 of wpa_supplicant.

I tried the ndis 0.12rc3 cvs but it errors when I compile.

Once I get:

Failed to initiate AP scan.

It just hangs there. There are no subsequent messages

"I saw similar issues with a scan for
specific SSID (scan_ssid=1), but broadcast SSID scan worked fine."

What value needs to be in my conf file to broadcast? I just followed the
instructions.

I've removed CONFIG_EAP_PSK=y from .config and recompiled okay. Config now
looks like this:

CONFIG_WIRELESS_EXTENSION=y
CONFIG_DRIVER_NDISWRAPPER=y

Thanks for your help

-----Original Message-----
From: hostap-bounces+andrew=duaneville.com at shmoo.com
[mailto:hostap-bounces+andrew=duaneville.com at shmoo.com] On Behalf Of Jouni
Malinen
Sent: 21 November 2004 05:16
To: hostap at shmoo.com
Subject: Re: Ndiswrapper +wpa_supplicant

On Sat, Nov 20, 2004 at 01:39:50PM -0000, Andrew Duane wrote:

> I wonder if someone would be so kind as to help me?

If you will provide some more information..

Which version of ndiswrapper are you using? With which NDIS driver and
which wlan card?

> I seem to have some trouble with running wpa_supplicant. Here is a dump of
> the error:

> [root at server1 wpa_supplicant-0.2.5]# wpa_supplicant -iwlan0
> -c/etc/wpa_supplicant.conf -dd

> Starting AP scan (specific SSID)
> Scan SSID - hexdump_ascii(len=10):
>      46 6f 75 6e 64 61 74 69 6f 6e                     Linksys
> Failed to initiate AP scan.

And what happened after this? I saw similar issues with a scan for
specific SSID (scan_ssid=1), but broadcast SSID scan worked fine. Please
also verify whether you can see the correct AP in 'iwlist wlan0 scan'
output and whether this includes wpa_ie information.

> And my .config before I did a make was:
> 
> CONFIG_EAP_PSK=y

You do not need EAP-PSK for WPA-PSK; it is an experimental EAP method
that is not likely to be deployed anywhere yet.

-- 
Jouni Malinen                                            PGP id EFC895FA
_______________________________________________
HostAP mailing list
HostAP at shmoo.com
http://lists.shmoo.com/mailman/listinfo/hostap




_______________________________________________
HostAP mailing list
HostAP at shmoo.com
http://lists.shmoo.com/mailman/listinfo/hostap







More information about the HostAP mailing list