Senao SL-2511CD Ext2

Yang-Hwee TAN tanyh at bii.a-star.edu.sg
Thu Jun 19 20:57:22 EDT 2003


Read on...

On Thu, 19 Jun 2003 15:47:27 +0200
Alberto Malvido <amalvido#miranda at pasarela.tsc.uvigo.es> wrote:

> 
> Thanks to all for your responses.
> 
> Yang-Hwee, I used yor How-To, and I compiled and installed hostap without error. But when I init Debian, there are errors like these:
> 
> PCI:Enabling device 00:09:0 (0000->0002)
> PCI:No Irq know for interrrupt pin A of device 00:09:0. Probably buggy MP table.
> Ricoh RL5C475 rev 80 PCI-to-CardBus at slot 00:09, mem 0x100000
> host opts [0]:[isa irq] [10 3/6/1] [no pci irq] [lat 168/176] [bus 2/5]
> ISA irqs(default)= 3,4,7,9,10,11 polling interval=100ms.
> pasport 0:PC-style at 0x378 (0x778) [PCSPP, TRISTATE, EPP]
> parport: irq 7 detected
> lp0: using parport0 (polling)
> cs:memory probe 0xa0000000-0xa0ffffff:clean
> 
> hostap-crypt:registered algorithm 'NULL'
> hostap_cs:hostap_cs 0.0.0 2002-10-12 (SSH Comunications Security Corp, Jouni Malinen)
> hostap_cs: (c) Jouni Malinen <jkmaline at cc.hut.fi>
> hostap_cs:CardServices release does not match!
> hostap_crypt:registered algorithm 'NULL' (deinit)
> 
> 
> I wrote next lines in hostap_cs.conf
> 	card "Senao SL-2511CD/SL-2511CDPLUS/SL-2511CDPLUSEXT2"
> 		version "INTERSIL", "HFA384x/IEEE", "Version 01.02"
> 		bind "hostap_cs"
> It`s this right?.
> 

for the above, i would recommend u to use manfid value instead. can't go wrong 
with the nos. and some OEMer's cards may get associated easily too although 
description may be different. :)


> I compiled Kernell with next issues:
> 
> [*] Prompt for development and/or incomplete code/drivers
> [ ] PCMCIA/Cardbus
> [*] Enable loadable module support
> [*] Set version information on all module symbols
> [*] Kernel module loader
> [*] 802.1d Ethernet Bridgind
> [*] Wireless LAN (nom-hamradio)
> 

oh... don't u need the pcmcia module as well? else where do u plug in your 
card to? direct PCI wireless cards? if you're using direct pci wireless 
card, you'll need to "make pci" for hostap, it's a different setup from 
your previous attempt.

hope this helps. maybe the other hostap debian user(s) can help on the 
kernel modules part...


cheers,
Yanghwee


> Thanks you very much.
> 
> 
> > use ...
> > make pccard
> > ref to my docs... http://pachome2.pacific.net.sg/~yanghwee/sub/How-To-wirelessAP.html
> > i used the same card n pcmcia adapter too.
> > disclaimer: my docs was written based on hostap(dated 2002-05-19).
> > have fun!
> > -yanghwee
> 
> On Wed, 18 Jun 2003 19:12:12 +0200
> Alberto Malvido <amalvido#miranda at pasarela.tsc.uvigo.es> wrote:
> > Hi all,
> >
> > I purchase one Senao SL-2511CD EXT2 802.11b card, and one PCI-PCMCIA RICOH adapter. I´m trying install hostap under Debian but i have some doubts.
> >
> > I don´t know the manfid of this card, the veersion and the others parameters that I must include in hostap_cs.conf file.
> > Also, I don´t know how compile the driver:
> > make pccard?
> > make pci?
> > make plx?
> > I have a 2.4.18 kernel, do I need install pcmcia_cs or can I use the pcmcia already installed?.
> >
> > If somebady have one How-to to install this card under Debian I would be greatefull.
> >
> > Thank you Very Much.
> >
> >
> 
> -- 
> Using M2, Opera's revolutionary e-mail client: http://www.opera.com/m2/
> _______________________________________________
> HostAP mailing list
> HostAP at shmoo.com
> http://lists.shmoo.com/mailman/listinfo/hostap



More information about the HostAP mailing list