<div dir="ltr"><div><div><div>Hi, <br><br></div>I am using hostapd 2-2 version in my all winner A20 cubieboard running on ubuntu 12.04. I have compile the source code. i t has compiled with out error. but when i run this is the log <br><br>{" <br> 1<b>414649556.126296: nl80211: Could not add multicast membership for vendor events: -2 (No such file or directory)<br>1414649556.126813: rfkill: initial event: idx=0 type=2 op=0 soft=0 hard=0<br>1414649556.126917: rfkill: initial event: idx=1 type=1 op=0 soft=0 hard=0<br>1414649556.126997: rfkill: initial event: idx=2 type=1 op=0 soft=0 hard=0<br>1414649556.128435: nl80211: Supported cipher 00-0f-ac:1<br>1414649556.128623: nl80211: Supported cipher 00-0f-ac:5<br>1414649556.128693: nl80211: Supported cipher 00-0f-ac:2<br>1414649556.128761: nl80211: Supported cipher 00-0f-ac:4<br>1414649556.129151: nl80211: Supported cipher 00-0f-ac:6<br>1414649556.129224: nl80211: Using driver-based off-channel TX<br>1414649556.129364: nl80211: Disable use_monitor with device_ap_sme since no monitor mode support detected<br>1414649556.129483: nl80211: interface wlan1 in phy phy0<br>1414649556.129840: nl80211: Set mode ifindex 5 iftype 3 (AP)<br>1414649556.130097: nl80211: Setup AP(wlan1) - device_ap_sme=1 use_monitor=0<br>1414649556.130295: nl80211: Subscribe to mgmt frames with AP handle 0xf16410 (device SME)<br>1414649556.130384: nl80211: Register frame type=0xd0 nl_handle=0xf16410 match=<br>1414649556.130613: nl80211: Register frame command failed (type=208): ret=-114 (Operation already in progress)<br>1414649556.130700: nl80211: Register frame match - hexdump(len=0): [NULL]<br>1414649556.130890: nl80211: Could not configure driver mode<br>1414649556.130963: nl80211: Remove monitor interface: refcount=0<br>1414649556.131036: nl80211: Remove beacon (ifindex=5)<br>1414649556.131266: netlink: Operstate: ifindex=5 linkmode=0 (kernel-control), operstate=6 (IF_OPER_UP)<br>1414649556.131475: nl80211: Set mode ifindex 5 iftype 2 (STATION)<br>1414649556.131699: nl80211: Teardown AP(wlan1) - device_ap_sme=1 use_monitor=0<br>1414649556.131794: nl80211 driver initialization failed.<br>1414649556.131894: hostapd_interface_deinit_free(0xf15298)<br>1414649556.132007: hostapd_interface_deinit_free: num_bss=1 conf->num_bss=1<br>1414649556.132076: hostapd_interface_deinit(0xf15298)<br>1414649556.132137: hostapd_bss_deinit: deinit bss wlan1<br>1414649556.132249: hostapd_cleanup(hapd=0xf15de8 (wlan1))<br>1414649556.132332: hostapd_free_hapd_data: Interface wlan1 wasn't started<br>1414649556.132395: hostapd_interface_deinit_free: driver=(nil) drv_priv=(nil) -> hapd_deinit<br>1414649556.132465: hostapd_interface_free(0xf15298)<br>1414649556.132523: hostapd_interface_free: free hapd 0xf15de8<br>1414649556.132587: hostapd_cleanup_iface(0xf15298)<br>1414649556.132646: hostapd_cleanup_iface_partial(0xf15298)<br>1414649556.132753: hostapd_cleanup_iface: free iface=0xf15298</b><br>"}<br></div>This is config file <br>"<b># WiFi Hotspot<br>interface=wlan1<br>driver=nl80211<br>#Access Point<br>ssid=myhotspot<br>hw_mode=g<br># WiFi Channel:<br>channel=1<br>logger_syslog=-1<br>logger_syslog_level=2<br>logger_stdout=-1<br>logger_stdout_level=2<br>#macaddr_acl=0<br>#auth_algs=1<br>#ignore_broadcast_ssid=0<br>#wpa=3<br>#wpa_passphrase=qwerty0987<br>#wpa_key_mgmt=WPA-PSK<br>#wpa_pairwise=TKIP<br>#rsn_pairwise=CCMP"<br><br></b></div>so please any one help me to make board as wifi hotspot<br><div><div><br><div><br clear="all"><div><div><br>-- <br><div dir="ltr"><br><div><br></div><div><br></div><div><br></div><div>With Regards,</div><div>M.Nithin Chakravrthi</div></div>
</div></div></div></div></div></div>