<div dir="ltr">Another question: Why the TXRate is limited to 54Mbps while in theory USB 3 should provide between 300 & 867Mbps</div><div class="gmail_extra"><br><br><div class="gmail_quote">On Tue, Jun 24, 2014 at 10:04 AM, Charles Moulliard <span dir="ltr"><<a href="mailto:ch007m@gmail.com" target="_blank">ch007m@gmail.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr">Thx Janusz for your reply and your help.<div><br></div><div>Here is more info collected based on your input. I have created a gist ticket with hostapd config, result to run the command 'iw list' and what is displayed in debug mode by hostapd --> <a href="https://gist.github.com/cmoulliard/17eba8ed42b81afb064d" target="_blank">https://gist.github.com/cmoulliard/17eba8ed42b81afb064d</a><div>
<br><div>Remark : The new config does not work now and I don't get an error in the log</div><div><br></div><div>Regards,</div><div><br></div></div></div></div><div class="gmail_extra"><div><div class="h5"><br><br><div class="gmail_quote">
On Tue, Jun 24, 2014 at 9:18 AM, Janusz Dziedzic <span dir="ltr"><<a href="mailto:janusz.dziedzic@tieto.com" target="_blank">janusz.dziedzic@tieto.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div>On 23 June 2014 13:09, Charles Moulliard <<a href="mailto:ch007m@gmail.com" target="_blank">ch007m@gmail.com</a>> wrote:<br>
> Hi,<br>
><br>
> Something goes wrong with my config of hostapd 2.2 on a linux kernel<br>
> (3.14.7-200.fc20.x86_64). I have plugged an Edmix AC200 (WIFI USB) and it<br>
> works fine using this driver<br>
> (<a href="https://github.com/abperiasamy/rtl8812AU_8821AU_linux" target="_blank">https://github.com/abperiasamy/rtl8812AU_8821AU_linux</a>) and setup (hostapd<br>
> 2.2 + dnsmaq) but I can't change the channel to a value higher than 48 and<br>
> bitrate is around 24Mbits/s (measured with iperf) between this machine and a<br>
> client (=MacBook pro)<br>
><br>
> What is the issue ?<br>
><br>
</div>64 - is DFS channel, so required HW that support radar detection +<br>
hostap config (country_code=, ieee80211d=1, ieee80211h=1)<br>
<div><div><br>
> sudo ./hostapd config_test.conf<br>
> Configuration file: config_test.conf<br>
> wlp0s20u2: IEEE 802.11 Configured channel (64) not found from the channel<br>
> list of current mode (2) IEEE 802.11a<br>
> wlp0s20u2: IEEE 802.11 Hardware does not support configured channel<br>
> Could not select hw_mode and channel. (-3)<br>
><br>
> More debug output available here :<br>
> <a href="https://gist.github.com/cmoulliard/81aa9c7dc60c366f4724" target="_blank">https://gist.github.com/cmoulliard/81aa9c7dc60c366f4724</a><br>
><br>
> iwlist wlp0s20u2 channel<br>
> wlp0s20u2 32 channels in total; available frequencies :<br>
> Channel 01 : 2.412 GHz<br>
> Channel 02 : 2.417 GHz<br>
> Channel 03 : 2.422 GHz<br>
> Channel 04 : 2.427 GHz<br>
> Channel 05 : 2.432 GHz<br>
> Channel 06 : 2.437 GHz<br>
> Channel 07 : 2.442 GHz<br>
> Channel 08 : 2.447 GHz<br>
> Channel 09 : 2.452 GHz<br>
> Channel 10 : 2.457 GHz<br>
> Channel 11 : 2.462 GHz<br>
> Channel 12 : 2.467 GHz<br>
> Channel 13 : 2.472 GHz<br>
> Channel 36 : 5.18 GHz<br>
> Channel 40 : 5.2 GHz<br>
> Channel 44 : 5.22 GHz<br>
> Channel 48 : 5.24 GHz<br>
> Channel 52 : 5.26 GHz<br>
> Channel 56 : 5.28 GHz<br>
> Channel 60 : 5.3 GHz<br>
> Channel 64 : 5.32 GHz<br>
> Channel 100 : 5.5 GHz<br>
> Channel 104 : 5.52 GHz<br>
> Channel 108 : 5.54 GHz<br>
> Channel 112 : 5.56 GHz<br>
> Channel 116 : 5.58 GHz<br>
> Channel 120 : 5.6 GHz<br>
> Channel 124 : 5.62 GHz<br>
> Channel 128 : 5.64 GHz<br>
> Channel 132 : 5.66 GHz<br>
> Channel 136 : 5.68 GHz<br>
> Channel 140 : 5.7 GHz<br>
> Current Frequency:5.24 GHz (Channel 48)<br>
><br>
</div></div>Please use iw list instead.<br>
<div><div><br>
> dabou@localhost Temp$ iwconfig<br>
><br>
> wlp0s20u2 IEEE 802.11a ESSID:"fuselab" Nickname:"<WIFI@REALTEK>"<br>
> Mode:Master Frequency:5.24 GHz Access Point: D8:50:E6:F3:96:C7<br>
> Bit Rate:54 Mb/s Sensitivity:0/0<br>
> Retry:off RTS thr:off Fragment thr:off<br>
> Power Management:off<br>
> Link Quality=66/100 Signal level=48/100 Noise level=0/100<br>
> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0<br>
> Tx excessive retries:0 Invalid misc:0 Missed beacon:0<br>
><br>
> Config used :<br>
><br>
> interface=wlp0s20u2<br>
> ssid=fuselab<br>
> #channel=48<br>
> channel=64<br>
><br>
> # WPA and WPA2 configuration<br>
> macaddr_acl=0<br>
> auth_algs=1<br>
> ignore_broadcast_ssid=0<br>
> wpa=3<br>
> wpa_passphrase=fuselab987<br>
> wpa_key_mgmt=WPA-PSK<br>
> wpa_pairwise=TKIP<br>
> rsn_pairwise=CCMP<br>
><br>
> # Hardware configuration<br>
> driver=nl80211<br>
> wme_enabled=1<br>
> ieee80211n=0<br>
> ieee80211ac=1<br>
> hw_mode=a<br>
><br>
</div></div>Here you can use (v)ht40/vht80 - as I remember correctly 80211ac=1<br>
required also 80211n=1.<br>
<br>
BR<br>
<span><font color="#888888">Janusz<br>
</font></span></blockquote></div><br><br clear="all"><div><br></div></div></div><div class="">-- <br><div dir="ltr"><div>Charles Moulliard</div><div>Apache Committer / Architect @RedHat</div><div>Twitter : @cmoulliard | Blog : <a href="http://cmoulliard.github.io" target="_blank"> http://cmoulliard.github.io</a></div>
<div><br></div></div>
</div></div>
</blockquote></div><br><br clear="all"><div><br></div>-- <br><div dir="ltr"><div>Charles Moulliard</div><div>Apache Committer / Architect @RedHat</div><div>Twitter : @cmoulliard | Blog : <a href="http://cmoulliard.github.io" target="_blank"> http://cmoulliard.github.io</a></div>
<div><br></div></div>
</div>