<div>Hi Matthieu,</div>
<div> </div>
<div>I was building the airo driver not as seperate module and when I statically set the wpa_enabled variable to non-zero, WPA PSK is working fine :-).</div>
<div> </div>
<div>* Aim for me is to set the driver to wpa or wep based on wpa_supplicant configuration file info. </div>
<div>* I believe wpa and wep cannot exists simultaneously(correct me if I am wrong). </div>
<div>* I prefer to use some ioctl calls from wpa_supplicant to driver to enable wpa or wep. </div>
<div> </div>
<div>Can you please share your thought in this?</div>
<div> </div>
<div>Thanks in Advance</div>
<div> </div>
<div><br><br> </div>
<div class="gmail_quote">On Mon, May 11, 2009 at 1:48 PM, linux newbie <span dir="ltr"><<a href="mailto:linux.newbie79@gmail.com">linux.newbie79@gmail.com</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="PADDING-LEFT: 1ex; MARGIN: 0px 0px 0px 0.8ex; BORDER-LEFT: #ccc 1px solid">
<div>Hi Matthieu,</div>
<div> </div>
<div>Many thanks for your reply.</div>
<div> </div>
<div>With the airo driver you mentioned, I coulnt receive the EAPOL messages. i.e wpa_supplicant_rx_eapol is not called.</div>
<div> </div>
<div>I have sent a mail regarding this but it is waiting for moderator approval as the length of message is long.</div>
<div> </div>
<div>Also below is the aironet card status. Will it work for WPA? or do I need to update to some other firmware?</div>
<div> </div>
<div># cat /proc/driver/aironet/eth1/Status <br>Status: WEP <br>Mode: 200<br>Signal Strength: 27<br>Signal Quality: 143<br>SSID: <br>AP: AllansfordAP04<br>Freq: 0<br>BitRate: 11mbs<br>Driver Version: airo.c 0.6 (Ben Reed & Javier Achirica)<br>
Device: 350 Series<br>Manufacturer: Cisco Systems<br>Firmware Version: 5.41<br>Radio type: 2<br>Country: 0<br>Hardware Version: 22<br>Software Version: 541<br>Software Subversion: 0<br>Boot block version: 150</div>
<div> </div>
<div>Thanks in Advance<br><br></div>
<div>
<div></div>
<div class="h5">
<div class="gmail_quote">On Mon, May 11, 2009 at 7:28 AM, matthieu castet <span dir="ltr"><<a href="mailto:castet.matthieu@free.fr" target="_blank">castet.matthieu@free.fr</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="PADDING-LEFT: 1ex; MARGIN: 0px 0px 0px 0.8ex; BORDER-LEFT: #ccc 1px solid">Hi,
<div><br><br>linux newbie wrote:<br>
<blockquote class="gmail_quote" style="PADDING-LEFT: 1ex; MARGIN: 0px 0px 0px 0.8ex; BORDER-LEFT: #ccc 1px solid"> Hi,<br><br>I am using airo net 350 client and linux kernel 2.6.26.<br><br>I downloaded latest airo driver that supports wpa from<br>
<a href="http://svn.gna.org/svn/airo-wpa/trunk/airo.c" target="_blank">http://svn.gna.org/svn/airo-wpa/trunk/airo.c</a><br><br></blockquote></div>Hm, it should be the one <a href="http://svn.gna.org/svn/airo-wpa/branches/kernel/" target="_blank">http://svn.gna.org/svn/airo-wpa/branches/kernel/</a><br>
The version in trunk is old and doesn't build with recent kernel.
<div><br><br><br><br>
<blockquote class="gmail_quote" style="PADDING-LEFT: 1ex; MARGIN: 0px 0px 0px 0.8ex; BORDER-LEFT: #ccc 1px solid">State: GROUP_HANDSHAKE -> COMPLETED<br>RTM_NEWLINK: operstate=1 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])<br>
Wireless event: cmd=0x8b15 len=20<br>Wireless event: new AP: 00:00:00:00:00:00<br>Setting scan request: 0 sec 100000 usec<br>Added BSSID 00:23:ab:be:90:70 into blacklist<br>CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys<br>
</blockquote></div>This event can be generated when we are not disassociated.<br><br>Can you post your kernel log ?<br><font color="#888888"><br><br>Matthieu<br></font></blockquote></div><br></div></div></blockquote></div>
<br>