Thank you Ambedkar!!<br>After I posted the message, I tried once again to make AP mode work.It finally worked.But I did not use hostapd.The card is activated by the inbuilt hostap driver and I could set master mode on the 
card.The Access Point was visible from all systems and I could connect other systems to it.<br>In the Access Point, it gave the message(dmesg) that the system associated and gave the hardware address of the associated machine 
also.But the ping does not work.I can&#39;t ping from the access point nor from the other laptops.<br>Do I need hostapd?If so what does this command do:<br>&nbsp;&nbsp; hostapd -B hostapd.conf<br><br>You have mentioned a .config file.Is
 it the hostapd.conf file?<br>Whenever I run the above command it says<br>&quot;Hostap Driver initialization failed&quot;<br>ioctl (SIOC..FLAG) No such device<br><br>Please do clarify.Moreover what is wpa_supplicant?Do I need it?
<br><br>Thank you once again<br><br>Regards<br>Archana.<br><br><div class="gmail_quote">On 23 Nov 2007 16:45:20 -0000, Ambedkar R &lt;<a href="mailto:ambedkar_r@rediffmail.com">ambedkar_r@rediffmail.com</a>&gt; wrote:<br>
<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;"><p>
&nbsp; <br>
Hi Archana,<br>
<br>
Bringing up the X86(Linux machine) as AP is very easy.All you should have that get it download the packages,<br>
<br>
1.hostapd<br>
Link: <a href="http://hostap.epitest.fi/hostapd/" target="_blank">http://hostap.epitest.fi/hostapd/</a><br>
Download the latest Stable release<br>
<br>
2.I think,prism2/2.5/3 works fine with hostap driver.<br>
<br>
3.You can find the .config file,get it modify it according to your <br>
card.<br>
<br>
Once you done,update me.<br>
<br>
Thanks<br>
Ambedkar.R<br>
<br>
On Thu, 22 Nov 2007 Archana Rajagopal wrote :</p><div><div></div><div class="Wj3C7c"><br>
&gt;Thank You Ambedkar!<br>
&gt;Actually the Linksys card worked on the old kernel(without any<br>
&gt;compilation).It automatically loaded orinoco_cs and hostap_cs, when I<br>
&gt;inserted the card and I could access the internet.But when I compiled the<br>
&gt;new kernel, I think I set something different in the configuration(though I<br>
&gt;dont remember doing anything different other than setting host ap options to<br>
&gt;&#39;Yes&#39; instead of modularize).So, do you mean that the absence of appropriate<br>
&gt;driver caused the bootup error?<br>
&gt;My goal is to make the card act as an access point.So I want hostap_cs<br>
&gt;driver to work on the card.Do I need hostapd(daemon) to actually set AP<br>
&gt;mode?I am new to this, I dont really understand how to make the Linksys<br>
&gt;WPC11 work as an access point.It will be very helpful if you could clarify.<br>
&gt;<br>
&gt;-Thank you<br>
&gt;Archana Rajagopal.<br>
&gt;<br>
&gt;<br>
&gt;<br>
&gt;<br>
&gt;On 22 Nov 2007 10:40:16 -0000, Ambedkar R &lt;<a href="mailto:ambedkar_r@rediffmail.com" target="_blank">ambedkar_r@rediffmail.com</a>&gt; wrote:<br>
&gt;<br>
&gt; &gt;<br>
&gt; &gt; Hi Archana,<br>
&gt; &gt;<br>
&gt; &gt; ORiNOCO card which you mentioned uses &quot;madwifi&quot; driver.But WPC11(Note book<br>
&gt; &gt; Adapter-B) uses its own driver(Linksys).So that may be the problem.And i<br>
&gt; &gt; dont think that you can use the WPC11 card on madwifi driver.<br>
&gt; &gt;<br>
&gt; &gt; Please let me know more details.<br>
&gt; &gt;<br>
&gt; &gt; Thanks<br>
&gt; &gt; Ambedkar.R<br>
&gt; &gt;<br>
&gt; &gt;<br>
&gt; &gt; On Wed, 21 Nov 2007 Archana Rajagopal wrote :<br>
&gt; &gt;<br>
&gt; &gt; &gt;Hi,<br>
&gt; &gt; &gt;&nbsp; &nbsp; I am using kernel version 2.6.18-2 .I tried compiling the kernel with<br>
&gt; &gt; &gt;HostAP and PCMCIA options as &#39;Yes&#39;.The system boots up if I use orinoco<br>
&gt; &gt; card<br>
&gt; &gt; &gt;but when I use Linksys WPC11(Prism card), it gives the following message:<br>
&gt; &gt; &gt;&nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &nbsp; &quot;CPU:0 Unexpected LVT TMR interrupt!!&quot;<br>
&gt; &gt; &gt;and then the system gets stuck there...it does not boot.<br>
&gt; &gt; &gt;<br>
&gt; &gt; &gt;Even if insert the card after boot...the system hangs...and I have to<br>
&gt; &gt; reboot<br>
&gt; &gt; &gt;it.<br>
&gt; &gt; &gt;<br>
&gt; &gt; &gt;One observation is :<br>
&gt; &gt; &gt;When I booted the system without any card and rebooted it.When it was<br>
&gt; &gt; about<br>
&gt; &gt; &gt;to shutdown, i inserted the Linksys card it showed the following<br>
&gt; &gt; messages:<br>
&gt; &gt; &gt;&quot;PCMCIA card inserted&quot;<br>
&gt; &gt; &gt;Registering device ...<br>
&gt; &gt; &gt;hostap_cs : Registered device xxx<br>
&gt; &gt; &gt;....<br>
&gt; &gt; &gt;<br>
&gt; &gt; &gt;Does it mean that it is trying to load hostap for that card?I did not<br>
&gt; &gt; &gt;understand.Please clarify.<br>
&gt; &gt; &gt;Thank you.<br>
&gt; &gt; &gt;<br>
&gt; &gt; &gt;--<br>
&gt; &gt; &gt;Regards<br>
&gt; &gt; &gt;Archana Rajagopal<br>
&gt; &gt; &gt;_______________________________________________<br>
&gt; &gt; &gt;HostAP mailing list<br>
&gt; &gt; &gt;<a href="mailto:HostAP@shmoo.com" target="_blank">HostAP@shmoo.com</a><br>
&gt; &gt; &gt;<a href="http://lists.shmoo.com/mailman/listinfo/hostap" target="_blank">http://lists.shmoo.com/mailman/listinfo/hostap</a><br>
&gt; &gt;<br>
&gt; &gt;<br>
&gt; &gt;<br>
&gt;<br>
&gt;<br>
&gt;--<br>
&gt;Regards<br>
&gt;Archana Rajagopal<br>

</div></div>
<br><br>
</blockquote></div><br><br clear="all"><br>-- <br>Regards<br>Archana Rajagopal