<DIV>
<DIV>
<DIV>
<DIV>Hi</DIV>
<DIV> </DIV>
<DIV>I have been so far unable to connect to my ZyXEL Wifi router while running ndiswrapper-1.2 and wpa_supplicant under FC3 (though all works fine under Windows XP on my dual boot PC). After my failed attempts at starting wpa_supplicant 0.3.9, I moved on to v. 0.4.3, but to no avail -- the output screen included below refers to 0.4.3.</DIV>
<DIV> </DIV>
<DIV>Did I set any parameters wrong? Any help as to how to get this interface up and running would be most appreciated!</DIV>
<DIV> </DIV>
<DIV><A href="mailto:pete_r880@yahoo.com">pete_r880@yahoo.com</A></DIV>
<DIV> </DIV>
<DIV>=========================================</DIV>
<DIV><FONT face=system># File: /etc/wpa_supplicant.conf</FONT></DIV>
<DIV><FONT size=2>
<P><FONT face=system>ctrl_interface=/var/run/wpa_supplicant</FONT></P>
<P><FONT face=system>network={<BR> ssid="mywnet"<BR> psk="longpassphrase"<BR> key_mgmt=WPA-PSK<BR> proto=WPA<BR>}</FONT></P>
<DIV>=========================================</DIV>
<DIV>Network interface</DIV>
<DIV> </DIV>
<DIV>[root@localhost ~]# ifconfig wlan0<BR><FONT face=system>wlan0 Link encap:Ethernet HWaddr 00:A0:C5:92:F8:ED<BR> BROADCAST MULTICAST MTU:1500 Metric:1<BR> RX packets:0 errors:0 dropped:0 overruns:0 frame:0<BR> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0<BR> collisions:0 txqueuelen:1000<BR> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)<BR> Memory:ed120000-ed121fff</FONT></DIV>
<DIV><FONT face=system><BR> </DIV></FONT></FONT></DIV>
<DIV><FONT size=2>
<DIV>[root@localhost ~]# iwconfig wlan0<BR><FONT face=system>Warning: Driver for device wlan0 recommend version 18 of Wireless Extension,<BR>but has been compiled with version 16, therefore some driver features<BR>may not be available...</FONT></DIV>
<DIV><FONT face=system>wlan0 IEEE 802.11g ESSID:off/any<BR> Mode:Managed Frequency:2.412GHz Access Point: 00:00:00:00:00:00<BR> Bit Rate:125Mb/s Tx-Power:10 dBm Sensitivity=0/3<BR> RTS thr:4096 B Fragment thr:4096 B<BR> Encryption key:off<BR> Power Management:off<BR> Link Quality:100 Signal level:0 Noise level:0<BR> Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0<BR> Tx excessive retries:0 Invalid misc:0 Missed beacon:0</FONT></DIV>
<DIV>=========================================</DIV>
<DIV> </DIV>
<DIV>[root@localhost ~]# ifconfig wlan0 up</DIV>
<DIV>[root@localhost ~]# wpa_supplicant -D ndiswrapper -i wlan0 -c /etc/wpa_supplicant.conf -dd<BR><FONT face=system>Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'ndiswrapper'<BR>Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'<BR>Reading configuration file '/etc/wpa_supplicant.conf'<BR>ctrl_interface='/var/run/wpa_supplicant'<BR>ctrl_interface_group=0<BR>eapol_version=1<BR>ap_scan=1<BR>fast_reauth=1<BR>Line: 264 - start of a new network block<BR>ssid - hexdump_ascii(len=8):<BR> 56 61 6c 68 61 6c 6c 61 mywnet<BR>PSK (ASCII passphrase) - hexdump_ascii(len=31): [REMOVED]<BR>key_mgmt: 0x2<BR>proto: 0x1<BR>PSK (from passphrase) - hexdump(len=32): [REMOVED]<BR>Priority group 0<BR> id=0 ssid='mywnet'<BR>Initializing interface (2)
'wlan0'<BR>ioctl[SIOCSIWPMKSA]: No such device<BR>Own MAC address: 00:a0:c5:92:f8:ed<BR>Setting scan request: 0 sec 100000 usec<BR>Using existing control interface directory.<BR>Wireless event: cmd=0x8b06 len=8<BR>State: DISCONNECTED -> SCANNING<BR>Starting AP scan (broadcast SSID)<BR>Scan timeout - try to get results<BR>Received 489 bytes of scan results (2 BSSes)<BR>Scan results: 2<BR>Selecting BSS from priority group 0<BR>0: 00:a0:c5:cc:27:42 ssid='mywnet' wpa_ie_len=24 rsn_ie_len=0 caps=0x11<BR> selected<BR>Trying to associate with 00:a0:c5:cc:27:42 (SSID='mywnet' freq=2447 MHz)<BR>Cancelling scan request<BR>WPA: clearing own WPA/RSN IE<BR>Automatic auth_alg selection: 0x1<BR>WPA: using IEEE 802.11i/D3.0<BR>WPA: Selected cipher suites: group 8 pairwise 8 key_mgmt 2<BR>WPA: set AP WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02<BR>WPA: clearing AP RSN IE<BR>WPA: using GTK TKIP<BR>WPA: using PTK TKIP<BR>WPA: using
KEY_MGMT WPA-PSK<BR>WPA: Set own WPA IE default - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01 00 00 50 f2 02 01 00 00 50 f2 02<BR>No keys have been configured - skip key clearing<BR>State: SCANNING -> ASSOCIATING<BR>Segmentation fault<BR></FONT></DIV>
<DIV>
<DIV>=========================================</DIV></DIV></FONT></DIV></DIV></DIV></DIV><p>
<hr size=1>Do you Yahoo!?<br>
Yahoo! Mail - Find what you need with new enhanced search. <a href="http://us.rd.yahoo.com/evt=29917/*http://info.mail.yahoo.com/mail_250">Learn more.</a>