P2P_FIND command failed from wpa_cli

Nilkanth Ahirrao nilkanth.ahirrao at gmail.com
Mon Jan 21 22:32:12 EST 2013


Hi Jouni,

Thank you very much for your prompt response.
Please find the iw list result as:
-------------------
Wiphy phy0
    Band 1:
        Capabilities: 0x872
            HT20/HT40
            Static SM Power Save
            RX Greenfield
            RX HT20 SGI
            RX HT40 SGI
            No RX STBC
            Max AMSDU length: 3839 bytes
            No DSSS/CCK HT40
        Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
        Minimum RX AMPDU time spacing: 4 usec (0x05)
        HT RX MCS rate indexes supported: 0-15, 32
        TX unequal modulation not supported
        HT TX Max spatial streams: 1
        HT TX MCS rate indexes supported may differ
        Frequencies:
            * 2412 MHz [1] (14.0 dBm)
            * 2417 MHz [2] (14.0 dBm)
            * 2422 MHz [3] (14.0 dBm)
            * 2427 MHz [4] (14.0 dBm)
            * 2432 MHz [5] (14.0 dBm)
            * 2437 MHz [6] (14.0 dBm)
            * 2442 MHz [7] (14.0 dBm)
            * 2447 MHz [8] (14.0 dBm)
            * 2452 MHz [9] (14.0 dBm)
            * 2457 MHz [10] (14.0 dBm)
            * 2462 MHz [11] (14.0 dBm)
            * 2467 MHz [12] (14.0 dBm) (passive scanning, no IBSS)
            * 2472 MHz [13] (14.0 dBm) (passive scanning, no IBSS)
        Bitrates (non-HT):
            * 1.0 Mbps
            * 2.0 Mbps (short preamble supported)
            * 5.5 Mbps (short preamble supported)
            * 11.0 Mbps (short preamble supported)
            * 6.0 Mbps
            * 9.0 Mbps
            * 12.0 Mbps
            * 18.0 Mbps
            * 24.0 Mbps
            * 36.0 Mbps
            * 48.0 Mbps
            * 54.0 Mbps
    max # scan SSIDs: 20
    Supported interface modes:
         * IBSS
         * managed
         * monitor
    Supported commands:
         * new_interface
         * set_interface
         * new_key
         * new_beacon
         * new_station
         * new_mpath
         * set_mesh_params
         * set_bss
         * authenticate
         * associate
         * deauthenticate
         * disassociate
         * join_ibss
         * Unknown command (68)
         * Unknown command (55)
         * Unknown command (57)
         * Unknown command (59)
         * Unknown command (67)
         * set_wiphy_netns
         * Unknown command (65)
         * Unknown command (66)
         * connect
         * disconnect
--------------------------------------
Please let me know if you need any further details.

Regards,
Nil

On Mon, Jan 21, 2013 at 3:28 PM, Jouni Malinen <j at w1.fi> wrote:

> On Sun, Jan 20, 2013 at 03:35:02PM +0530, Nilkanth Ahirrao wrote:
> > I would like to connect to  P2P device  and transfer the data.
> >
> > Platform : X86,Ubuntu Kernel 3.0 later
>
> Which WLAN driver are you using? Are you sure it supports P2P? Please
> send "iw list" output showing driver capabilities.
>
> --
> Jouni Malinen                                            PGP id EFC895FA
> _______________________________________________
> HostAP mailing list
> HostAP at lists.shmoo.com
> http://lists.shmoo.com/mailman/listinfo/hostap
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.shmoo.com/pipermail/hostap/attachments/20130122/05d7e37f/attachment.htm 


More information about the HostAP mailing list