[PATCH 1/6] update nl80211_copy.h

Johannes Berg johannes at sipsolutions.net
Thu Sep 16 09:03:11 EDT 2010


From: Johannes Berg <johannes.berg at intel.com>

Signed-off-by: Johannes Berg <johannes.berg at intel.com>
---
 src/drivers/nl80211_copy.h |  212 +++++++++++++++++++++++++++++++++++++-------
 1 files changed, 180 insertions(+), 32 deletions(-)

diff --git a/src/drivers/nl80211_copy.h b/src/drivers/nl80211_copy.h
index 2ea3ede..f0518b0 100644
--- a/src/drivers/nl80211_copy.h
+++ b/src/drivers/nl80211_copy.h
@@ -40,6 +40,43 @@
  */
 
 /**
+ * DOC: Frame transmission/registration support
+ *
+ * Frame transmission and registration support exists to allow userspace
+ * management entities such as wpa_supplicant react to management frames
+ * that are not being handled by the kernel. This includes, for example,
+ * certain classes of action frames that cannot be handled in the kernel
+ * for various reasons.
+ *
+ * Frame registration is done on a per-interface basis and registrations
+ * cannot be removed other than by closing the socket. It is possible to
+ * specify a registration filter to register, for example, only for a
+ * certain type of action frame. In particular with action frames, those
+ * that userspace registers for will not be returned as unhandled by the
+ * driver, so that the registered application has to take responsibility
+ * for doing that.
+ *
+ * The type of frame that can be registered for is also dependent on the
+ * driver and interface type. The frame types are advertised in wiphy
+ * attributes so applications know what to expect.
+ *
+ * NOTE: When an interface changes type while registrations are active,
+ *       these registrations are ignored until the interface type is
+ *       changed again. This means that changing the interface type can
+ *       lead to a situation that couldn't otherwise be produced, but
+ *       any such registrations will be dormant in the sense that they
+ *       will not be serviced, i.e. they will not receive any frames.
+ *
+ * Frame transmission allows userspace to send for example the required
+ * responses to action frames. It is subject to some sanity checking,
+ * but many frames can be transmitted. When a frame was transmitted, its
+ * status is indicated to the sending socket.
+ *
+ * For more technical details, see the corresponding command descriptions
+ * below.
+ */
+
+/**
  * enum nl80211_commands - supported nl80211 commands
  *
  * @NL80211_CMD_UNSPEC: unspecified command to catch errors
@@ -52,6 +89,8 @@
  *	%NL80211_ATTR_WIPHY_CHANNEL_TYPE, %NL80211_ATTR_WIPHY_RETRY_SHORT,
  *	%NL80211_ATTR_WIPHY_RETRY_LONG, %NL80211_ATTR_WIPHY_FRAG_THRESHOLD,
  *	and/or %NL80211_ATTR_WIPHY_RTS_THRESHOLD.
+ *	However, for setting the channel, see %NL80211_CMD_SET_CHANNEL
+ *	instead, the support here is for backward compatibility only.
  * @NL80211_CMD_NEW_WIPHY: Newly created wiphy, response to get request
  *	or rename notification. Has attributes %NL80211_ATTR_WIPHY and
  *	%NL80211_ATTR_WIPHY_NAME.
@@ -130,7 +169,7 @@
  * 	%NL80211_ATTR_REG_RULE_POWER_MAX_ANT_GAIN and
  * 	%NL80211_ATTR_REG_RULE_POWER_MAX_EIRP.
  * @NL80211_CMD_REQ_SET_REG: ask the wireless core to set the regulatory domain
- * 	to the the specified ISO/IEC 3166-1 alpha2 country code. The core will
+ * 	to the specified ISO/IEC 3166-1 alpha2 country code. The core will
  * 	store this as a valid request and then query userspace for it.
  *
  * @NL80211_CMD_GET_MESH_PARAMS: Get mesh networking properties for the
@@ -256,7 +295,9 @@
  *	auth and assoc steps. For this, you need to specify the SSID in a
  *	%NL80211_ATTR_SSID attribute, and can optionally specify the association
  *	IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_MAC,
- *	%NL80211_ATTR_WIPHY_FREQ and %NL80211_ATTR_CONTROL_PORT.
+ *	%NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT,
+ *	%NL80211_ATTR_CONTROL_PORT_ETHERTYPE and
+ *	%NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT.
  *	It is also sent as an event, with the BSSID and response IEs when the
  *	connection is established or failed to be established. This can be
  *	determined by the STATUS_CODE attribute.
@@ -299,16 +340,20 @@
  *	rate selection. %NL80211_ATTR_IFINDEX is used to specify the interface
  *	and @NL80211_ATTR_TX_RATES the set of allowed rates.
  *
- * @NL80211_CMD_REGISTER_ACTION: Register for receiving certain action frames
- *	(via @NL80211_CMD_ACTION) for processing in userspace. This command
- *	requires an interface index and a match attribute containing the first
- *	few bytes of the frame that should match, e.g. a single byte for only
- *	a category match or four bytes for vendor frames including the OUI.
- *	The registration cannot be dropped, but is removed automatically
- *	when the netlink socket is closed. Multiple registrations can be made.
- * @NL80211_CMD_ACTION: Action frame TX request and RX notification. This
- *	command is used both as a request to transmit an Action frame and as an
- *	event indicating reception of an Action frame that was not processed in
+ * @NL80211_CMD_REGISTER_FRAME: Register for receiving certain mgmt frames
+ *	(via @NL80211_CMD_FRAME) for processing in userspace. This command
+ *	requires an interface index, a frame type attribute (optional for
+ *	backward compatibility reasons, if not given assumes action frames)
+ *	and a match attribute containing the first few bytes of the frame
+ *	that should match, e.g. a single byte for only a category match or
+ *	four bytes for vendor frames including the OUI. The registration
+ *	cannot be dropped, but is removed automatically when the netlink
+ *	socket is closed. Multiple registrations can be made.
+ * @NL80211_CMD_REGISTER_ACTION: Alias for @NL80211_CMD_REGISTER_FRAME for
+ *	backward compatibility
+ * @NL80211_CMD_FRAME: Management frame TX request and RX notification. This
+ *	command is used both as a request to transmit a management frame and
+ *	as an event indicating reception of a frame that was not processed in
  *	kernel code, but is for us (i.e., which may need to be processed in a
  *	user space application). %NL80211_ATTR_FRAME is used to specify the
  *	frame contents (including header). %NL80211_ATTR_WIPHY_FREQ (and
@@ -318,17 +363,29 @@
  *	operational channel). When called, this operation returns a cookie
  *	(%NL80211_ATTR_COOKIE) that will be included with the TX status event
  *	pertaining to the TX request.
- * @NL80211_CMD_ACTION_TX_STATUS: Report TX status of an Action frame
- *	transmitted with %NL80211_CMD_ACTION. %NL80211_ATTR_COOKIE identifies
+ * @NL80211_CMD_ACTION: Alias for @NL80211_CMD_FRAME for backward compatibility.
+ * @NL80211_CMD_FRAME_TX_STATUS: Report TX status of a management frame
+ *	transmitted with %NL80211_CMD_FRAME. %NL80211_ATTR_COOKIE identifies
  *	the TX command and %NL80211_ATTR_FRAME includes the contents of the
  *	frame. %NL80211_ATTR_ACK flag is included if the recipient acknowledged
  *	the frame.
+ * @NL80211_CMD_ACTION_TX_STATUS: Alias for @NL80211_CMD_FRAME_TX_STATUS for
+ *	backward compatibility.
  * @NL80211_CMD_SET_CQM: Connection quality monitor configuration. This command
  *	is used to configure connection quality monitoring notification trigger
  *	levels.
  * @NL80211_CMD_NOTIFY_CQM: Connection quality monitor notification. This
  *	command is used as an event to indicate the that a trigger level was
  *	reached.
+ * @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ
+ *	and %NL80211_ATTR_WIPHY_CHANNEL_TYPE) the given interface (identifed
+ *	by %NL80211_ATTR_IFINDEX) shall operate on.
+ *	In case multiple channels are supported by the device, the mechanism
+ *	with which it switches channels is implementation-defined.
+ *	When a monitor interface is given, it can only switch channel while
+ *	no other interfaces are operating to avoid disturbing the operation
+ *	of any other interfaces, and other interfaces will again take
+ *	precedence when they are used.
  *
  * @NL80211_CMD_MAX: highest used command number
  * @__NL80211_CMD_AFTER_LAST: internal use
@@ -418,9 +475,12 @@ enum nl80211_commands {
 
 	NL80211_CMD_SET_TX_BITRATE_MASK,
 
-	NL80211_CMD_REGISTER_ACTION,
-	NL80211_CMD_ACTION,
-	NL80211_CMD_ACTION_TX_STATUS,
+	NL80211_CMD_REGISTER_FRAME,
+	NL80211_CMD_REGISTER_ACTION = NL80211_CMD_REGISTER_FRAME,
+	NL80211_CMD_FRAME,
+	NL80211_CMD_ACTION = NL80211_CMD_FRAME,
+	NL80211_CMD_FRAME_TX_STATUS,
+	NL80211_CMD_ACTION_TX_STATUS = NL80211_CMD_FRAME_TX_STATUS,
 
 	NL80211_CMD_SET_POWER_SAVE,
 	NL80211_CMD_GET_POWER_SAVE,
@@ -428,6 +488,8 @@ enum nl80211_commands {
 	NL80211_CMD_SET_CQM,
 	NL80211_CMD_NOTIFY_CQM,
 
+	NL80211_CMD_SET_CHANNEL,
+
 	/* add new commands above here */
 
 	/* used to define NL80211_CMD_MAX below */
@@ -626,6 +688,15 @@ enum nl80211_commands {
  *	request, the driver will assume that the port is unauthorized until
  *	authorized by user space. Otherwise, port is marked authorized by
  *	default in station mode.
+ * @NL80211_ATTR_CONTROL_PORT_ETHERTYPE: A 16-bit value indicating the
+ *	ethertype that will be used for key negotiation. It can be
+ *	specified with the associate and connect commands. If it is not
+ *	specified, the value defaults to 0x888E (PAE, 802.1X). This
+ *	attribute is also used as a flag in the wiphy information to
+ *	indicate that protocols other than PAE are supported.
+ * @NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT: When included along with
+ *	%NL80211_ATTR_CONTROL_PORT_ETHERTYPE, indicates that the custom
+ *	ethertype frames used for key negotiation must not be encrypted.
  *
  * @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver.
  *	We recommend using nested, driver-specific attributes within this.
@@ -695,7 +766,16 @@ enum nl80211_commands {
  *	is used with %NL80211_CMD_SET_TX_BITRATE_MASK.
  *
  * @NL80211_ATTR_FRAME_MATCH: A binary attribute which typically must contain
- *	at least one byte, currently used with @NL80211_CMD_REGISTER_ACTION.
+ *	at least one byte, currently used with @NL80211_CMD_REGISTER_FRAME.
+ * @NL80211_ATTR_FRAME_TYPE: A u16 indicating the frame type/subtype for the
+ *	@NL80211_CMD_REGISTER_FRAME command.
+ * @NL80211_ATTR_TX_FRAME_TYPES: wiphy capability attribute, which is a
+ *	nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing
+ *	information about which frame types can be transmitted with
+ *	%NL80211_CMD_FRAME.
+ * @NL80211_ATTR_RX_FRAME_TYPES: wiphy capability attribute, which is a
+ *	nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing
+ *	information about which frame types can be registered for RX.
  *
  * @NL80211_ATTR_ACK: Flag attribute indicating that the frame was
  *	acknowledged by the recipient.
@@ -709,6 +789,15 @@ enum nl80211_commands {
  *	NL80211_CMD_AUTHENTICATE, NL80211_CMD_DEAUTHENTICATE,
  *	NL80211_CMD_DISASSOCIATE.
  *
+ * @NL80211_ATTR_AP_ISOLATE: (AP mode) Do not forward traffic between stations
+ *	connected to this BSS.
+ *
+ * @NL80211_ATTR_WIPHY_TX_POWER_SETTING: Transmit power setting type. See
+ *      &enum nl80211_tx_power_setting for possible values.
+ * @NL80211_ATTR_WIPHY_TX_POWER_LEVEL: Transmit power level in signed mBm units.
+ *      This is used in association with @NL80211_ATTR_WIPHY_TX_POWER_SETTING
+ *      for non-automatic settings.
+ *
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
  */
@@ -864,6 +953,18 @@ enum nl80211_attrs {
 
 	NL80211_ATTR_LOCAL_STATE_CHANGE,
 
+	NL80211_ATTR_AP_ISOLATE,
+
+	NL80211_ATTR_WIPHY_TX_POWER_SETTING,
+	NL80211_ATTR_WIPHY_TX_POWER_LEVEL,
+
+	NL80211_ATTR_TX_FRAME_TYPES,
+	NL80211_ATTR_RX_FRAME_TYPES,
+	NL80211_ATTR_FRAME_TYPE,
+
+	NL80211_ATTR_CONTROL_PORT_ETHERTYPE,
+	NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -919,8 +1020,10 @@ enum nl80211_attrs {
  * @NL80211_IFTYPE_WDS: wireless distribution interface
  * @NL80211_IFTYPE_MONITOR: monitor interface receiving all frames
  * @NL80211_IFTYPE_MESH_POINT: mesh point
+ * @NL80211_IFTYPE_P2P_CLIENT: P2P client
+ * @NL80211_IFTYPE_P2P_GO: P2P group owner
  * @NL80211_IFTYPE_MAX: highest interface type number currently defined
- * @__NL80211_IFTYPE_AFTER_LAST: internal use
+ * @NUM_NL80211_IFTYPES: number of defined interface types
  *
  * These values are used with the %NL80211_ATTR_IFTYPE
  * to set the type of an interface.
@@ -935,10 +1038,12 @@ enum nl80211_iftype {
 	NL80211_IFTYPE_WDS,
 	NL80211_IFTYPE_MONITOR,
 	NL80211_IFTYPE_MESH_POINT,
+	NL80211_IFTYPE_P2P_CLIENT,
+	NL80211_IFTYPE_P2P_GO,
 
 	/* keep last */
-	__NL80211_IFTYPE_AFTER_LAST,
-	NL80211_IFTYPE_MAX = __NL80211_IFTYPE_AFTER_LAST - 1
+	NUM_NL80211_IFTYPES,
+	NL80211_IFTYPE_MAX = NUM_NL80211_IFTYPES - 1
 };
 
 /**
@@ -947,11 +1052,14 @@ enum nl80211_iftype {
  * Station flags. When a station is added to an AP interface, it is
  * assumed to be already associated (and hence authenticated.)
  *
+ * @__NL80211_STA_FLAG_INVALID: attribute number 0 is reserved
  * @NL80211_STA_FLAG_AUTHORIZED: station is authorized (802.1X)
  * @NL80211_STA_FLAG_SHORT_PREAMBLE: station is capable of receiving frames
  *	with short barker preamble
  * @NL80211_STA_FLAG_WME: station is WME/QoS capable
  * @NL80211_STA_FLAG_MFP: station uses management frame protection
+ * @NL80211_STA_FLAG_MAX: highest station flag number currently defined
+ * @__NL80211_STA_FLAG_AFTER_LAST: internal use
  */
 enum nl80211_sta_flags {
 	__NL80211_STA_FLAG_INVALID,
@@ -1064,14 +1172,17 @@ enum nl80211_mpath_flags {
  * information about a mesh path.
  *
  * @__NL80211_MPATH_INFO_INVALID: attribute number 0 is reserved
- * @NL80211_ATTR_MPATH_FRAME_QLEN: number of queued frames for this destination
- * @NL80211_ATTR_MPATH_SN: destination sequence number
- * @NL80211_ATTR_MPATH_METRIC: metric (cost) of this mesh path
- * @NL80211_ATTR_MPATH_EXPTIME: expiration time for the path, in msec from now
- * @NL80211_ATTR_MPATH_FLAGS: mesh path flags, enumerated in
+ * @NL80211_MPATH_INFO_FRAME_QLEN: number of queued frames for this destination
+ * @NL80211_MPATH_INFO_SN: destination sequence number
+ * @NL80211_MPATH_INFO_METRIC: metric (cost) of this mesh path
+ * @NL80211_MPATH_INFO_EXPTIME: expiration time for the path, in msec from now
+ * @NL80211_MPATH_INFO_FLAGS: mesh path flags, enumerated in
  * 	&enum nl80211_mpath_flags;
- * @NL80211_ATTR_MPATH_DISCOVERY_TIMEOUT: total path discovery timeout, in msec
- * @NL80211_ATTR_MPATH_DISCOVERY_RETRIES: mesh path discovery retries
+ * @NL80211_MPATH_INFO_DISCOVERY_TIMEOUT: total path discovery timeout, in msec
+ * @NL80211_MPATH_INFO_DISCOVERY_RETRIES: mesh path discovery retries
+ * @NL80211_MPATH_INFO_MAX: highest mesh path information attribute number
+ *	currently defind
+ * @__NL80211_MPATH_INFO_AFTER_LAST: internal use
  */
 enum nl80211_mpath_info {
 	__NL80211_MPATH_INFO_INVALID,
@@ -1100,6 +1211,8 @@ enum nl80211_mpath_info {
  * @NL80211_BAND_ATTR_HT_CAPA: HT capabilities, as in the HT information IE
  * @NL80211_BAND_ATTR_HT_AMPDU_FACTOR: A-MPDU factor, as in 11n
  * @NL80211_BAND_ATTR_HT_AMPDU_DENSITY: A-MPDU density, as in 11n
+ * @NL80211_BAND_ATTR_MAX: highest band attribute currently defined
+ * @__NL80211_BAND_ATTR_AFTER_LAST: internal use
  */
 enum nl80211_band_attr {
 	__NL80211_BAND_ATTR_INVALID,
@@ -1120,6 +1233,7 @@ enum nl80211_band_attr {
 
 /**
  * enum nl80211_frequency_attr - frequency attributes
+ * @__NL80211_FREQUENCY_ATTR_INVALID: attribute number 0 is reserved
  * @NL80211_FREQUENCY_ATTR_FREQ: Frequency in MHz
  * @NL80211_FREQUENCY_ATTR_DISABLED: Channel is disabled in current
  *	regulatory domain.
@@ -1131,6 +1245,9 @@ enum nl80211_band_attr {
  *	on this channel in current regulatory domain.
  * @NL80211_FREQUENCY_ATTR_MAX_TX_POWER: Maximum transmission power in mBm
  *	(100 * dBm).
+ * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
+ *	currently defined
+ * @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
  */
 enum nl80211_frequency_attr {
 	__NL80211_FREQUENCY_ATTR_INVALID,
@@ -1150,9 +1267,13 @@ enum nl80211_frequency_attr {
 
 /**
  * enum nl80211_bitrate_attr - bitrate attributes
+ * @__NL80211_BITRATE_ATTR_INVALID: attribute number 0 is reserved
  * @NL80211_BITRATE_ATTR_RATE: Bitrate in units of 100 kbps
  * @NL80211_BITRATE_ATTR_2GHZ_SHORTPREAMBLE: Short preamble supported
  *	in 2.4 GHz band.
+ * @NL80211_BITRATE_ATTR_MAX: highest bitrate attribute number
+ *	currently defined
+ * @__NL80211_BITRATE_ATTR_AFTER_LAST: internal use
  */
 enum nl80211_bitrate_attr {
 	__NL80211_BITRATE_ATTR_INVALID,
@@ -1208,6 +1329,7 @@ enum nl80211_reg_type {
 
 /**
  * enum nl80211_reg_rule_attr - regulatory rule attributes
+ * @__NL80211_REG_RULE_ATTR_INVALID: attribute number 0 is reserved
  * @NL80211_ATTR_REG_RULE_FLAGS: a set of flags which specify additional
  * 	considerations for a given frequency range. These are the
  * 	&enum nl80211_reg_rule_flags.
@@ -1224,6 +1346,9 @@ enum nl80211_reg_type {
  * 	If you don't have one then don't send this.
  * @NL80211_ATTR_POWER_RULE_MAX_EIRP: the maximum allowed EIRP for
  * 	a given frequency range. The value is in mBm (100 * dBm).
+ * @NL80211_REG_RULE_ATTR_MAX: highest regulatory rule attribute number
+ *	currently defined
+ * @__NL80211_REG_RULE_ATTR_AFTER_LAST: internal use
  */
 enum nl80211_reg_rule_attr {
 	__NL80211_REG_RULE_ATTR_INVALID,
@@ -1275,6 +1400,9 @@ enum nl80211_reg_rule_flags {
  * @__NL80211_SURVEY_INFO_INVALID: attribute number 0 is reserved
  * @NL80211_SURVEY_INFO_FREQUENCY: center frequency of channel
  * @NL80211_SURVEY_INFO_NOISE: noise level of channel (u8, dBm)
+ * @NL80211_SURVEY_INFO_MAX: highest survey info attribute number
+ *	currently defined
+ * @__NL80211_SURVEY_INFO_AFTER_LAST: internal use
  */
 enum nl80211_survey_info {
 	__NL80211_SURVEY_INFO_INVALID,
@@ -1439,6 +1567,7 @@ enum nl80211_channel_type {
  * enum nl80211_bss - netlink attributes for a BSS
  *
  * @__NL80211_BSS_INVALID: invalid
+ * @NL80211_BSS_BSSID: BSSID of the BSS (6 octets)
  * @NL80211_BSS_FREQUENCY: frequency in MHz (u32)
  * @NL80211_BSS_TSF: TSF of the received probe response/beacon (u64)
  * @NL80211_BSS_BEACON_INTERVAL: beacon interval of the (I)BSS (u16)
@@ -1482,6 +1611,12 @@ enum nl80211_bss {
 
 /**
  * enum nl80211_bss_status - BSS "status"
+ * @NL80211_BSS_STATUS_AUTHENTICATED: Authenticated with this BSS.
+ * @NL80211_BSS_STATUS_ASSOCIATED: Associated with this BSS.
+ * @NL80211_BSS_STATUS_IBSS_JOINED: Joined to this IBSS.
+ *
+ * The BSS status is a BSS attribute in scan dumps, which
+ * indicates the status the interface has wrt. this BSS.
  */
 enum nl80211_bss_status {
 	NL80211_BSS_STATUS_AUTHENTICATED,
@@ -1592,8 +1727,8 @@ enum nl80211_tx_rate_attributes {
 
 /**
  * enum nl80211_band - Frequency band
- * @NL80211_BAND_2GHZ - 2.4 GHz ISM band
- * @NL80211_BAND_5GHZ - around 5 GHz band (4.9 - 5.7 GHz)
+ * @NL80211_BAND_2GHZ: 2.4 GHz ISM band
+ * @NL80211_BAND_5GHZ: around 5 GHz band (4.9 - 5.7 GHz)
  */
 enum nl80211_band {
 	NL80211_BAND_2GHZ,
@@ -1631,9 +1766,9 @@ enum nl80211_attr_cqm {
 
 /**
  * enum nl80211_cqm_rssi_threshold_event - RSSI threshold event
- * @NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW - The RSSI level is lower than the
+ * @NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW: The RSSI level is lower than the
  *      configured threshold
- * @NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH - The RSSI is higher than the
+ * @NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH: The RSSI is higher than the
  *      configured threshold
  */
 enum nl80211_cqm_rssi_threshold_event {
@@ -1641,4 +1776,17 @@ enum nl80211_cqm_rssi_threshold_event {
 	NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH,
 };
 
+
+/**
+ * enum nl80211_tx_power_setting - TX power adjustment
+ * @NL80211_TX_POWER_AUTOMATIC: automatically determine transmit power
+ * @NL80211_TX_POWER_LIMITED: limit TX power by the mBm parameter
+ * @NL80211_TX_POWER_FIXED: fix TX power to the mBm parameter
+ */
+enum nl80211_tx_power_setting {
+	NL80211_TX_POWER_AUTOMATIC,
+	NL80211_TX_POWER_LIMITED,
+	NL80211_TX_POWER_FIXED,
+};
+
 #endif /* __LINUX_NL80211_H */
-- 
1.7.1



More information about the HostAP mailing list