WEP-shared is failing...

Dan Williams dcbw at redhat.com
Mon Dec 17 21:14:00 EST 2007


On Tue, 2007-12-18 at 07:40 +0530, Raghavendra. S wrote:
> Hi,
> 
>   Tried with hex key...still failing...
> ----------------------------------------------------------------------------------
> ctrl_interface=/var/run/wpa_supplicant
> ap_scan=1
> 
> network={
>         ssid="3Com"
>         key_mgmt=NONE
>         wep_key0=76F6B7657D
>         wep_tx_keyidx=0
>         auth_alg=SHARED
> }
> ----------------------------------------------------------------------------------------
> 
> if you see below log...i have following three lines...
> 
> ioctl[SIOCSIWFREQ]: Operation not supported
> ioctl[SIOCSIWESSID]: Network is unreachable
> ioctl[SIOCSIWAP]: Network is unreachable

The Marvell vendor driver returns ENETUNREACH from SIOCSIWESSID adn
SIOCSIWAP when it can't find the SSID to associate with, or when the
security parameters of the network don't match what the driver has been
configured for.  Basically, the configuration you have and the scan
result that the driver has don't match up, or the network wasn't found
during the pre-association scan.  Can you provide the output of 'iwlist
ethX scan' for the 3Com network you want to connect to?

Dan

> is this a problem..or some thing else?
> 
> 
> 
> 
> 
> On 12/18/07, Dan Williams <dcbw at redhat.com> wrote:
> > On Tue, 2007-12-18 at 07:22 +0530, Raghavendra. S wrote:
> > > Hi All,
> > >
> > >  I tried to test wpa supplicant for auth_alg=SHARED, but failing to
> > > connect with AP,
> > > My supplicant.conf file configuration is all below.
> > >
> > > ----------------------start------------------------------------------------------------------
> > >
> > > ctrl_interface=/var/run/wpa_supplicant
> > >
> > > network={
> > >         ssid="3Com"
> > >         key_mgmt=NONE
> > >         auth_alg=SHARED
> > >         wep_key0="raghu123456"
> >
> > Are you trying to use a WEP passphrase here?  I don't think
> > wpa_supplicant supports WEP passphrase hashing.  Try a hex key here
> > instead.
> >
> > Dan
> >
> >
> > >         wep_tx_keyidx=0
> > > }
> > > ----------------------end-------------------------------------------------------------------
> > >
> > > I got following failure logs,
> > >
> > > # ./wpa_supplicant -ieth0 -Dwext -c ./files/wpa_supplicant.sharedWEP -w -ddd
> > > Initializing interface 'eth0' conf './files/wpa_supplicant.sharedWEP'
> > > driver 'wext' ctrl_interface 'N/A' bridge 'N/A'
> > > Configuration file './files/wpa_supplicant.sharedWEP' ->
> > > '/mnt/nfs/./files/wpa_supplicant.sharedWEP'
> > > Reading configuration file '/mnt/nfs/./files/wpa_supplicant.sharedWEP'
> > > ctrl_interface='/var/run/wpa_supplicant'
> > > Line: 4 - start of a new network block
> > > ssid - hexdump_ascii(len=4):
> > >      33 43 6f 6d                                       3Com
> > > key_mgmt: 0x4
> > > auth_alg: 0x2
> > > wep_key0 - hexdump(len=11): [REMOVED]
> > > wep_tx_keyidx=0 (0x0)
> > > Priority group 0
> > >    id=0 ssid='3Com'
> > > Initializing interface (2) 'eth0'
> > > EAPOL: SUPP_PAE entering state DISCONNECTED
> > > EAPOL: KEY_RX entering state NO_KEY_RECEIVE
> > > EAPOL: SUPP_BE entering state INITIALIZE
> > > EAP: EAP entering state DISABLED
> > > EAPOL: External notification - portEnabled=0
> > > EAPOL: External notification - portValid=0
> > > ioctl[SIOCSIWPMKSA]: Invalid argument
> > > SIOCGIWRANGE: WE(compiled)=22 WE(source)=15 enc_capa=0x0
> > >   capabilities: key_mgmt 0x0 enc 0x3
> > > WEXT: Operstate: linkmode=1, operstate=5
> > > Own MAC address: 00:13:e0:9e:9b:2e
> > > wpa_driver_wext_set_wpa
> > > wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
> > > wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
> > > wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
> > > wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
> > > wpa_driver_wext_set_countermeasures
> > > wpa_driver_wext_set_drop_unencrypted
> > > Setting scan request: 0 sec 100000 usec
> > > Added interface eth0
> > > RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
> > > Wireless event: cmd=0x8b06 len=8
> > > State: DISCONNECTED -> SCANNING
> > > Starting AP scan (broadcast SSID)
> > > Trying to get current scan results first without requesting a new scan
> > > to speed up initial association
> > > Received 416 bytes of scan results (5 BSSes)
> > > Scan results: 5
> > > Selecting BSS from priority group 0
> > > Try to find WPA-enabled AP
> > > 0: 00:90:4c:91:00:01 ssid='linksys' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
> > >    skip - no WPA/RSN IE
> > > 1: 00:0f:cb:fe:2f:5f ssid='3Com' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
> > >    skip - no WPA/RSN IE
> > > 2: 02:1b:77:03:c6:24 ssid='Enaru_Ser' wpa_ie_len=0 rsn_ie_len=0 caps=0x12
> > >    skip - no WPA/RSN IE
> > > 3: 02:e0:98:04:50:3e ssid='kk' wpa_ie_len=0 rsn_ie_len=0 caps=0x2
> > >    skip - no WPA/RSN IE
> > > 4: 00:1c:10:21:94:bb ssid='linksysWRT150N' wpa_ie_len=0 rsn_ie_len=0 caps=0x1
> > >    skip - no WPA/RSN IE
> > > Try to find non-WPA AP
> > > 0: 00:90:4c:91:00:01 ssid='linksys' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
> > >    skip - SSID mismatch
> > > 1: 00:0f:cb:fe:2f:5f ssid='3Com' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
> > >    selected non-WPA AP 00:0f:cb:fe:2f:5f ssid='3Com'
> > > Trying to associate with 00:0f:cb:fe:2f:5f (SSID='3Com' freq=2412 MHz)
> > > Cancelling scan request
> > > WPA: clearing own WPA/RSN IE
> > > Automatic auth_alg selection: 0x1
> > > Overriding auth_alg selection: 0x2
> > > WPA: clearing AP WPA IE
> > > WPA: clearing AP RSN IE
> > > WPA: clearing own WPA/RSN IE
> > > No keys have been configured - skip key clearing
> > > wpa_driver_wext_set_key: alg=1 key_idx=0 set_tx=1 seq_len=0 key_len=11
> > > wpa_driver_wext_set_drop_unencrypted
> > > State: SCANNING -> ASSOCIATING
> > > wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
> > > WEXT: Operstate: linkmode=-1, operstate=5
> > > wpa_driver_wext_associate
> > > ioctl[SIOCSIWFREQ]: Operation not supported
> > > ioctl[SIOCSIWESSID]: Network is unreachable
> > > ioctl[SIOCSIWAP]: Network is unreachable
> > > Association request to the driver failed
> > > Setting authentication timeout: 5 sec 0 usec
> > > EAPOL: External notification - portControl=ForceAuthorized
> > > RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
> > > Wireless event: cmd=0x8b06 len=8
> > > RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
> > > Wireless event: cmd=0x8b15 len=20
> > > Wireless event: new AP: 00:00:00:00:00:00
> > > Added BSSID 00:0f:cb:fe:2f:5f into blacklist
> > > CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
> > > State: ASSOCIATING -> DISCONNECTED
> > > wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
> > > WEXT: Operstate: linkmode=-1, operstate=5
> > > EAPOL: External notification - portEnabled=0
> > > EAPOL: External notification - portValid=0
> > > RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
> > > Wireless event: cmd=0x8b15 len=20
> > > Wireless event: new AP: 00:00:00:00:00:00
> > > Added BSSID 00:00:00:00:00:00 into blacklist
> > > CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
> > > State: DISCONNECTED -> DISCONNECTED
> > > wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
> > > WEXT: Operstate: linkmode=-1, operstate=5
> > > EAPOL: External notification - portEnabled=0
> > > EAPOL: External notification - portValid=0
> > > Authentication with 00:00:00:00:00:00 timed out.
> > > BSSID 00:00:00:00:00:00 blacklist count incremented to 2
> > > wpa_driver_wext_set_key: alg=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
> > > wpa_driver_wext_set_key: alg=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
> > > wpa_driver_wext_set_key: alg=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
> > > wpa_driver_wext_set_key: alg=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
> > > State: DISCONNECTED -> DISCONNECTED
> > > wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
> > > WEXT: Operstate: linkmode=-1, operstate=5
> > > EAPOL: External notification - portEnabled=0
> > > EAPOL: External notification - portValid=0
> > > Setting scan request: 0 sec 0 usec
> > > State: DISCONNECTED -> SCANNING
> > > Starting AP scan (broadcast SSID)
> > > RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
> > > Wireless event: cmd=0x8b19 len=8
> > > Received 416 bytes of scan results (5 BSSes)
> > > Scan results: 5
> > > Selecting BSS from priority group 0
> > > Try to find WPA-enabled AP
> > > 0: 00:90:4c:91:00:01 ssid='linksys' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
> > >    skip - no WPA/RSN IE
> > > 1: 00:0f:cb:fe:2f:5f ssid='3Com' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
> > >    skip - no WPA/RSN IE
> > > 2: 02:1b:77:03:c6:24 ssid='Enaru_Ser' wpa_ie_len=0 rsn_ie_len=0 caps=0x12
> > >    skip - no WPA/RSN IE
> > > 3: 02:e0:98:04:50:3e ssid='kk' wpa_ie_len=0 rsn_ie_len=0 caps=0x2
> > >    skip - no WPA/RSN IE
> > > 4: 00:1c:10:21:94:bb ssid='linksysWRT150N' wpa_ie_len=0 rsn_ie_len=0 caps=0x1
> > >    skip - no WPA/RSN IE
> > > Try to find non-WPA AP
> > > 0: 00:90:4c:91:00:01 ssid='linksys' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
> > >    skip - SSID mismatch
> > > 1: 00:0f:cb:fe:2f:5f ssid='3Com' wpa_ie_len=0 rsn_ie_len=0 caps=0x11
> > >    selected non-WPA AP 00:0f:cb:fe:2f:5f ssid='3Com'
> > > Trying to associate with 00:0f:cb:fe:2f:5f (SSID='3Com' freq=2412 MHz)
> > > Cancelling scan request
> > > WPA: clearing own WPA/RSN IE
> > > Automatic auth_alg selection: 0x1
> > > Overriding auth_alg selection: 0x2
> > > WPA: clearing AP WPA IE
> > > WPA: clearing AP RSN IE
> > > WPA: clearing own WPA/RSN IE
> > > No keys have been configured - skip key clearing
> > > wpa_driver_wext_set_key: alg=1 key_idx=0 set_tx=1 seq_len=0 key_len=11
> > > wpa_driver_wext_set_drop_unencrypted
> > > State: SCANNING -> ASSOCIATING
> > > wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
> > > WEXT: Operstate: linkmode=-1, operstate=5
> > > wpa_driver_wext_associate
> > > ioctl[SIOCSIWFREQ]: Operation not supported
> > > ioctl[SIOCSIWESSID]: Network is unreachable
> > > ioctl[SIOCSIWAP]: Network is unreachable
> > > Association request to the driver failed
> > > Setting authentication timeout: 5 sec 0 usec
> > > EAPOL: External notification - portControl=ForceAuthorized
> > > RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
> > > Wireless event: cmd=0x8b06 len=8
> > > RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
> > > Wireless event: cmd=0x8b15 len=20
> > > Wireless event: new AP: 00:00:00:00:00:00
> > > BSSID 00:0f:cb:fe:2f:5f blacklist count incremented to 2
> > > CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
> > > State: ASSOCIATING -> DISCONNECTED
> > > wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
> > > WEXT: Operstate: linkmode=-1, operstate=5
> > > EAPOL: External notification - portEnabled=0
> > > EAPOL: External notification - portValid=0
> > > RTM_NEWLINK: operstate=0 ifi_flags=0x1003 ([UP])
> > > Wireless event: cmd=0x8b15 len=20
> > > Wireless event: new AP: 00:00:00:00:00:00
> > > BSSID 00:00:00:00:00:00 blacklist count incremented to 3
> > > CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
> > > State: DISCONNECTED -> DISCONNECTED
> > > wpa_driver_wext_set_operstate: operstate 0->0 (DORMANT)
> > > WEXT: Operstate: linkmode=-1, operstate=5
> > > EAPOL: External notification - portEnabled=0
> > > EAPOL: External notification - portValid=0
> > >
> > >
> > > Please tell me why it is failing?
> > >
> > >
> >
> >
> 
> 




More information about the HostAP mailing list