WPA on Ibook G3 running ubuntu?

josh josh at vnetworx.net
Mon Mar 21 18:04:55 EST 2005


Is there anyway to get WPA working on a ibook G3 (Airport card) running 
ubuntu? WPA Supplicant spits this out in the log: 

root at ibook:/home/sniper # wpa_supplicant -c /etc/wpa_supplicant.conf -w -dd 
 -ieth1
Initializing interface 'eth1' conf '/etc/wpa_supplicant.conf' driver 
'default'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
Line: 1 - start of a new network block
ssid - hexdump_ascii(len=27):
    44 53 34 32 34 6b 64 6b 73 6c 6b 64 6c 6b 34 32   DS424kdkslkdlk42
    32 33 34 32 64 64 66 73 6b 64 73                  2342ddfskds
proto: 0x1
scan_ssid=1 (0x1)
key_mgmt: 0x2
PSK (ASCII passphrase) - hexdump_ascii(len=28): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 0
  id=0 ssid='Removed as to not be flamed'
Initializing interface (2) 'eth1'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Own MAC address: 00:30:65:03:1d:88
wpa_driver_hostap_set_wpa: enabled=1
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
ioctl[PRISM2_IOCTL_HOSTAPD]: Operation not supported
Failed to set encryption.
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
ioctl[PRISM2_IOCTL_HOSTAPD]: Operation not supported
Failed to set encryption.
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
ioctl[PRISM2_IOCTL_HOSTAPD]: Operation not supported
Failed to set encryption.
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
ioctl[PRISM2_IOCTL_HOSTAPD]: Operation not supported
Failed to set encryption.
wpa_driver_hostap_set_countermeasures: enabled=0
wpa_driver_hostap_set_drop_unencrypted: enabled=1
Setting scan request: 0 sec 100000 usec
l2_packet_receive - recv: Network is down
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=27):
    44 53 34 32 34 6b 64 6b 73 6c 6b 64 6c 6b 34 32   DS424kdkslkdlk42
    32 33 34 32 64 64 66 73 6b 64 73                  2342ddfskds
ioctl[PRISM2_IOCTL_HOSTAPD]: Operation not supported
Failed to initiate AP scan.
Setting scan request: 10 sec 0 usec
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Scan timeout - try to get results
ioctl[SIOCGIWSCAN]: Operation not supported
Scan results: -1
Failed to get scan results - try scanning again
Setting scan request: 1 sec 0 usec
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Starting AP scan (broadcast SSID)
ioctl[SIOCSIWSCAN{,EXT}]: Operation not supported
Failed to initiate AP scan.
Setting scan request: 10 sec 0 usec
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Scan timeout - try to get results
ioctl[SIOCGIWSCAN]: Operation not supported
Scan results: -1
Failed to get scan results - try scanning again
Setting scan request: 1 sec 0 usec
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=27):
    44 53 34 32 34 6b 64 6b 73 6c 6b 64 6c 6b 34 32   DS424kdkslkdlk42
    32 33 34 32 64 64 66 73 6b 64 73                  2342ddfskds
ioctl[PRISM2_IOCTL_HOSTAPD]: Operation not supported
Failed to initiate AP scan.
Setting scan request: 10 sec 0 usec
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Signal 2 received - terminating
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_hostap_set_wpa: enabled=0
ioctl[PRISM2_IOCTL_HOSTAPD]: Operation not supported
wpa_driver_hostap_set_drop_unencrypted: enabled=0
wpa_driver_hostap_set_countermeasures: enabled=0 

 

Am i doomed or what? :) 


Thank you,
 -Josh P 




More information about the HostAP mailing list