Lost in configuring wpa_supplicant and driverloader

Oliver G. spam at fuckup.homelinux.com
Tue Jun 7 06:54:18 EDT 2005


Hello all,

For days I have been trying to get wpa_supplicant working on my D-Link
GWL-G520+ (TI ACX111 chipset) - without success.
Without wpa, the connection is working fine in ad-hoc mode connected to a
ipw2100.
However, things look different when enabling WPA: I just cannot get a
working connection. Attached are some log files and the output of
wpa_supplicant after starting up.
Unfortunately, I don't have the experience to see what is going wrong. A
google search didn't show any useful results, either. So I would be glad
if someone could point me in the right direction.


dmesg:
eth2: prism2_param: unknown param 15
driverloader: ndisWrapParseWPAInformationElements: unknown authentication 0
eth2: prism2_param: unknown param 23


wpa_supplicant -i eth2 -c /etc/wpa_supplicant.conf -dd -Dhostap:
Initializing interface 'eth2' conf '/etc/wpa_supplicant.conf' driver 'hostap'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group=0
eapol_version=1
ap_scan=2
fast_reauth=1
Line: 290 - start of a new network block
ssid - hexdump_ascii(len=10):
     74 65 73 74 20 61 64 68 6f 63                     test adhoc
mode=1 (0x1)
proto: 0x1
key_mgmt: 0x10
pairwise: 0x1
group: 0x8
PSK (ASCII passphrase) - hexdump_ascii(len=17): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 0
   id=0 ssid='test adhoc'
Initializing interface (2) 'eth2'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Own MAC address: 00:11:95:47:66:11
wpa_driver_hostap_set_wpa: enabled=1
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_hostap_set_countermeasures: enabled=0
wpa_driver_hostap_set_drop_unencrypted: enabled=1
Setting scan request: 0 sec 100000 usec
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth2' added
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth2' added
Trying to associate with SSID 'test adhoc'
Cancelling scan request
Automatic auth_alg selection: 0x1
ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Operation not supported
WPA: Set cipher suites based on configuration
WPA: Selected cipher suites: group 8 pairwise 1 key_mgmt 16
WPA: using GTK TKIP
WPA: using PTK NONE
WPA: using KEY_MGMT WPA-NONE
WPA: Own WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01
00 00 50 f200 01 00 00 50 f2 00
No keys have been configured - skip key clearing
wpa_driver_hostap_set_key: alg=TKIP key_idx=0 set_tx=1 seq_len=6 key_len=32
ioctl[PRISM2_IOCTL_HOSTAPD]: Invalid argument
Failed to set encryption.
wpa_driver_hostap_set_drop_unencrypted: enabled=1
wpa_driver_hostap_associate
ioctl[PRISM2_IOCTL_PRISM2_PARAM]: Operation not supported
hostap: Failed to configure ieee_802_1x param
wpa_driver_hostap_set_key: alg=TKIP key_idx=0 set_tx=1 seq_len=6 key_len=32
ioctl[PRISM2_IOCTL_HOSTAPD]: Invalid argument
Failed to set encryption.
Cancelling authentication timeout
EAPOL: External notification - portControl=ForceAuthorized
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Signal 2 received - terminating
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_hostap_set_wpa: enabled=0
wpa_driver_hostap_set_drop_unencrypted: enabled=0
wpa_driver_hostap_set_countermeasures: enabled=0

wpa_supplicant.conf:
ctrl_interface=/var/run/wpa_supplicant
ctrl_interface_group=0
eapol_version=1
 ap_scan=2
fast_reauth=1

network={
        ssid="test adhoc"
        mode=1
        proto=WPA
        key_mgmt=WPA-NONE
        pairwise=NONE
        group=TKIP
        psk="secret passphrase"
}


On the ipw laptop, wpa_supplicant.conf is the same, and wpa_supplicant
shows these lines after startup:
Initializing interface 'eth1' conf '/etc/wpa_supplicant.conf' driver 'ipw'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
ctrl_interface='/var/run/wpa_supplicant'
ctrl_interface_group=0
eapol_version=1
ap_scan=2
fast_reauth=1
Line: 290 - start of a new network block
ssid - hexdump_ascii(len=10):
     74 65 73 74 20 61 64 68 6f 63                     test adhoc
mode=1 (0x1)
proto: 0x1
key_mgmt: 0x10
pairwise: 0x1
group: 0x8
PSK (ASCII passphrase) - hexdump_ascii(len=17): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 0
   id=0 ssid='test adhoc'
Initializing interface (2) 'eth1'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_ipw_init is called
Own MAC address: 00:0c:f1:17:cb:41
wpa_driver_ipw_set_wpa: enabled=1
wpa_driver_ipw_set_key: alg=none key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_ipw_set_key: alg=none key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_ipw_set_key: alg=none key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_ipw_set_key: alg=none key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_ipw_set_countermeasures: enabled=0
wpa_driver_ipw_set_drop_unencrypted: enabled=1
Setting scan request: 0 sec 100000 usec
Using existing control interface directory.
bind(PF_UNIX): Address already in use
ctrl_iface exists, but does not allow connections - assuming it was
leftover from forced program termination
Successfully replaced leftover ctrl_iface socket
'/var/run/wpa_supplicant/eth1'
Wireless event: cmd=0x8b06 len=8
Trying to associate with SSID 'test adhoc'
Cancelling scan request
Automatic auth_alg selection: 0x1
wpa_driver_ipw_set_auth_alg: auth_alg=0x1
WPA: Set cipher suites based on configuration
WPA: Selected cipher suites: group 8 pairwise 1 key_mgmt 16
WPA: using GTK TKIP
WPA: using PTK NONE
WPA: using KEY_MGMT WPA-NONE
WPA: Own WPA IE - hexdump(len=24): dd 16 00 50 f2 01 01 00 00 50 f2 02 01
00 00 50 f2 00 01 00 00 50 f2 00
No keys have been configured - skip key clearing
wpa_driver_ipw_set_key: alg=TKIP key_idx=0 set_tx=1 seq_len=6 key_len=32
wpa_driver_ipw_set_drop_unencrypted: enabled=1
wpa_driver_ipw_set_key: alg=TKIP key_idx=0 set_tx=1 seq_len=6 key_len=32
Cancelling authentication timeout
EAPOL: External notification - portControl=ForceAuthorized
RTM_NEWLINK, IFLA_IFNAME: Interface 'eth1' added
Wireless event: cmd=0x8b15 len=20
Wireless event: new AP: 00:00:00:00:00:00
Disconnect event - ignore in IBSS/WPA-None mode
Wireless event: cmd=0x8b1a len=23
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Signal 2 received - terminating
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_ipw_set_wpa: enabled=0
wpa_driver_ipw_set_drop_unencrypted: enabled=0
wpa_driver_ipw_set_countermeasures: enabled=0



Thanks in advance,

Oliver



More information about the HostAP mailing list