wpa_supplicant and hostap driver - no association with AP

Zdenek Pizl zdenek.pizl at systinet.com
Tue Jun 22 13:18:30 EDT 2004


Hi,

 Suddenly I cannot associate my wifi with an AP (Orinoco AP600)

there is an output from wpa_supplicant :

EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_hostap_set_wpa: enabled=1
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_countermeasures: enabled=0
wpa_driver_hostap_set_drop_unencrypted: enabled=1
Setting scan request: 0 sec 100000 usec
l2_packet_receive - recv: Network is down
Starting AP scan (specific SSID)
Scan SSID - hexdump_ascii(len=8):
     53 59 53 54 49 4e 45 54                           SYSTINET
ioctl[PRISM2_IOCTL_HOSTAPD]: Operation not supported
Failed to initiate AP scan.
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0
idleWhile=0
Scan timeout - try to get results
Received 0 bytes of scan results (0 BSSes)
Scan results: 0
No suitable AP found.
Setting scan request: 5 sec 0 usec
Signal 2 received - terminating
wpa_driver_hostap_set_key: alg=none key_idx=0 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=1 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=2 set_tx=0 seq_len=0
key_len=0
wpa_driver_hostap_set_key: alg=none key_idx=3 set_tx=0 seq_len=0
key_len=0
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
wpa_driver_hostap_set_wpa: enabled=0
wpa_driver_hostap_set_drop_unencrypted: enabled=0
wpa_driver_hostap_set_countermeasures: enabled=0

** end of output **

What is wrong, a day before I did it smoothly ...


prism 2.5, STA firmware 1.7.4
hostap driver 0.2.3
wpa_supplicant 0.2.3

-- 
Zdenek Pizl
Systinet Corporation
Vinohradska 190
130 00 Praha 3





More information about the HostAP mailing list