Regression with 0.3.2?

Romano Giannetti romanol at upco.es
Tue Dec 21 05:44:47 EST 2004


Hi Jouni, hi all, 

   I'm back... trying to make my wifi card work. I have a new problem with
   wpa_supplicant 0.3.2. Resumed: with 0.3.1 authentication worked, now it
   fails. In neither case I managed to have the traffic going on (see 
   http://www.dea.icai.upco.es/romano/wifi/report5-0.txt ). I failed with
   driverloader too, but this will go in another message. 

   Note: the full report is available at 
   http://www.dea.icai.upco.es/romano/wifi/report6.txt
   (the list manager said the message was too big...)
         

   Running wpa_supplicant 0.3.2 as ever: 

***start 0.3.2 log****
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'ndiswrapper'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
eapol_version=1
ap_scan=1
Line: 7 - start of a new network block
ssid - hexdump_ascii(len=9):
     75 70 63 6f 5f 77 6c 61 6e                        upco_wlan       
key_mgmt: 0x8
eap methods - hexdump(len=2): 19 00
identity - hexdump_ascii(len=16):
     72 6f 6d 61 6e 6f 40 75 70 63 6f 6e 74 2e 65 73   romano at upcont.es
password - hexdump_ascii(len=9): [REMOVED]
phase2 - hexdump_ascii(len=13):
     61 75 74 68 3d 4d 53 43 48 41 50 56 32            auth=MSCHAPV2   
Priority group 0
   id=0 ssid='upco_wlan'
Initializing interface (2) 'wlan0'
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Own MAC address: 00:0b:9d:00:b2:6e
Setting scan request: 0 sec 100000 usec
Starting AP scan (broadcast SSID)
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Scan timeout - try to get results
Received 1096 bytes of scan results (4 BSSes)
Scan results: 4
Selecting BSS from priority group 0
0: 00:11:5c:77:82:40 ssid='upco_wlan' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
1: 00:11:5c:6b:90:e0 ssid='upco_wlan' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
2: 00:11:5c:6b:8f:20 ssid='upco_wlan' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
3: 00:11:5c:6b:8f:60 ssid='upco_wlan' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
   selected non-WPA AP 00:11:5c:77:82:40 ssid='upco_wlan'
Trying to associate with 00:11:5c:77:82:40 (SSID='upco_wlan' freq=2427 MHz)
Cancelling scan request
Automatic auth_alg selection: 0x1
No keys have been configured - skip key clearing
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - portControl=Auto
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
EAPOL: Port Timers tick - authWhile=0 heldWhile=0 startWhen=0 idleWhile=0
Authentication with 00:00:00:00:00:00 timed out.
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
Setting scan request: 0 sec 0 usec
Starting AP scan (broadcast SSID)
Signal 2 received - terminating
No keys have been configured - skip key clearing
EAPOL: External notification - portEnabled=0
EAPOL: External notification - portValid=0
*** end 0.3.2 log ***

   But it used to work (the authentication, I mean) with 0.3.1:

***start 0.3.1 log***
Initializing interface 'wlan0' conf '/etc/wpa_supplicant.conf' driver 'ndiswrapper'
Configuration file '/etc/wpa_supplicant.conf' -> '/etc/wpa_supplicant.conf'
Reading configuration file '/etc/wpa_supplicant.conf'
eapol_version=1
ap_scan=1

[bits removed: see http://www.dea.icai.upco.es/romano/wifi/report6.txt ]

Received 1032 bytes of scan results (4 BSSes)
Scan results: 4
Selecting BSS from priority group 0
0: 00:11:5c:77:82:40 ssid='upco_wlan' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
1: 00:11:5c:6b:90:e0 ssid='upco_wlan' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
2: 00:11:5c:6b:8c:20 ssid='upco_wlan' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
3: 00:11:5c:6b:8f:20 ssid='upco_wlan' wpa_ie_len=0 rsn_ie_len=0
   skip - no WPA/RSN IE
   selected non-WPA AP 00:11:5c:77:82:40 ssid='upco_wlan'
Trying to associate with 00:11:5c:77:82:40 (SSID='upco_wlan' freq=2427 MHz)
Cancelling scan request
Automatic auth_alg selection: 0x1
No keys have been configured - skip key clearing
Setting authentication timeout: 5 sec 0 usec
EAPOL: External notification - portControl=Auto
Wireless event: cmd=0x8c02 len=137
Custom wireless event: 'ASSOCINFO(ReqIEs=00097570636f5f776c616e010482848b96dd180050f20101000050f20001000050f20501000050f2000000 RespIEs=010482848b96)'
Association info event
req_ies - hexdump(len=43): 00 09 75 70 63 6f 5f 77 6c 61 6e 01 04 82 84 8b 96 dd 18 00 50 f2 01 01 00 00 50 f2 00 01 00 00 50 f2 05 01 00 00 50 f2 00 00 00
resp_ies - hexdump(len=6): 01 04 82 84 8b 96
assoc_wpa_ie - hexdump(len=26): dd 18 00 50 f2 01 01 00 00 50 f2 00 01 00 00 50 f2 05 01 00 00 50 f2 00 00 00
RX EAPOL from 00:11:5c:6b:90:e0
RX EAPOL - hexdump(len=46): 01 00 00 05 01 01 00 05 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

[bits removed: see http://www.dea.icai.upco.es/romano/wifi/report6.txt ]

EAPOL: RX IEEE 802.1X ver=1 type=3 len=44 EAPOL-Key: type=1 key_length=13 key_index=0x83
EAPOL: EAPOL-Key key signature verified
EAPOL: using part of EAP keying material data encryption key - hexdump(len=13): [REMOVED]
EAPOL: Setting dynamic WEP key: unicast keyidx 3 len 13
EAPOL: all required EAPOL-Key frames received
WPA: EAPOL processing complete
Cancelling authentication timeout
EAPOL: SUPP_PAE entering state AUTHENTICATED

*** end 0.3.1 log***

The configuration file is the following: 

***
#ctrl_interface=/var/run/wpa_supplicant
#trl_interface_group=0

eapol_version=1
ap_scan=1

network={
        ssid="upco_wlan"
	key_mgmt=IEEE8021X
 	eap=PEAP
	#eapol_flags=3
	#scan_ssid=1
	identity="romano at upcont.es"
	password="[REMOVED]"
	phase2="auth=MSCHAPV2"
	# priority=1
}
***

What could have happened? 

Thanks,
       Romano

    


-- 
Romano Giannetti             -  Univ. Pontificia Comillas (Madrid, Spain)
Electronic Engineer - phone +34 915 422 800 ext 2416  fax +34 915 596 569



More information about the HostAP mailing list