two pci->pcmcia + two senao setup

norbert testowich norbi234 at gmx.de
Wed Aug 18 07:41:44 EDT 2004


Hello,

I have the same problem! Did you find a solution?

Greeting 

	Norbi

Am Montag, 16. Februar 2004 21:14 schrieb Bas van Tiel:
> Currently I'm having trouble with the following setup:
>
> - ABIT BH6 + Pentium 166
> - 2X  Ricoh Co Ltd RL5c475
> - 2X Senao 100 mW
>
> The following output is given by hostap:
>
> hostap_crypt: registered algorithm 'NULL'
> hostap_cs: CVS (Jouni Malinen <jkmaline at cc.hut.fi>)
> hostap_cs: setting Vcc=33 (constant)
> hostap_cs: CS_EVENT_CARD_INSERTION
> hostap_cs: setting Vcc=33 (from config)
> Checking CFTABLE_ENTRY 0x01 (default 0x01)
> IO window settings: cfg->io.nwin=1 dflt.io.nwin=1
> io->flags = 0x0046, io.base=0x0000, len=64
> hostap_cs: Registered netdevice wifi0
> hostap_cs: index 0x01: Vcc 3.3, irq 10, io 0x0100-0x013f
> prism2_hw_init: initialized in 200 ms
> wifi0: NIC: id=0x800c v1.0.0
> wifi0: PRI: id=0x15 v1.1.0
> wifi0: STA: id=0x1f v1.4.9
> wifi0: defaulting to bogus WDS frame as a workaround for firmware bug in
> Host AP mode WDS
>  wifi0: registered netdevice wlan0
>  hostap_cs: setting Vcc=33 (constant)
>  hostap_cs: CS_EVENT_CARD_INSERTION
>  hostap_cs: setting Vcc=33 (from config)
>  Checking CFTABLE_ENTRY 0x01 (default 0x01)
>  IO window settings: cfg->io.nwin=1 dflt.io.nwin=1
>  io->flags = 0x0046, io.base=0x0000, len=64
>  hostap_cs: Registered netdevice wifi1
>  hostap_cs: index 0x01: Vcc 3.3, irq 12, io 0x0140-0x017f
>  hostap_cs: assuming no Primary image in flash - card initialization not
> complete d
>  wifi1: test Genesis mode with HCR 0x1f
>  prism2_pccard_cor_sreset: original COR 41
>  prism2_pccard_genesis_sreset: original COR 41
>  Readback test failed, HCR 0x1f write 00 e1 a1 ff read 00 87 a1 a7
>  wifi1: test Genesis mode with HCR 0x0f
>  prism2_pccard_cor_sreset: original COR 41
>  prism2_pccard_genesis_sreset: original COR 41
>  Readback test succeeded, HCR 0x0f
>  prism2_pccard_genesis_sreset: original COR 41
>  wifi1: registered netdevice wlan1
>  wifi1: cannot get RID fdc6 (len=12) - no PRI f/w
>  wifi1: cannot get RID fdc6 (len=12) - no PRI f/w
>  wifi1: cannot get RID fdc1 (len=2) - no PRI f/w
>  wifi1: cannot get RID fc06 (len=2) - no PRI f/w
>  wifi1: cannot get RID fd42 (len=6) - no PRI f/w
>  wifi1: cannot get RID fc0e (len=34) - no PRI f/w
>  wifi1: cannot get RID fc84 (len=2) - no PRI f/w
>  wifi1: cannot get RID fc83 (len=2) - no PRI f/w
>  wifi1: cannot get RID fc82 (len=2) - no PRI f/w
>  wifi1: cannot get RID fc09 (len=2) - no PRI f/w
>  wifi1: cannot get RID fd48 (len=2) - no PRI f/w
>  wlan1: cannot get RID fdc6 (len=12) - no PRI f/w
>  wlan1: cannot get RID fdc6 (len=12) - no PRI f/w
>  wlan1: cannot get RID fdc1 (len=2) - no PRI f/w
>  wlan1: cannot get RID fc06 (len=2) - no PRI f/w
>  wlan1: cannot get RID fd42 (len=6) - no PRI f/w
>  wlan1: cannot get RID fc0e (len=34) - no PRI f/w
>  wlan1: cannot get RID fc84 (len=2) - no PRI f/w
>  wlan1: cannot get RID fc83 (len=2) - no PRI f/w
>  wlan1: cannot get RID fc82 (len=2) - no PRI f/w
>  wlan1: cannot get RID fc09 (len=2) - no PRI f/w
>  wlan1: cannot get RID fd48 (len=2) - no PRI f/w
>
>
>
> Interface wlan0 works correctly but wlan1 won't work, it also reports
> that the primary flash is not available. Both Ricoh and Senao work properly
> in a single setup. Has somebody already tried this ?
>
>
> Feel free to send me an email
>
> Bas
>
>
> ----- End forwarded message -----



More information about the HostAP mailing list