WDS speed issues revisited

[Dave]

Still no luck with CVS as of about 15 minutes ago...

Maybe something is wrong with my settings? I included current iwconfig
output from each WDS box below as well as startup settings which are applied
on bootup for each.




WDS1:

wlan0     IEEE 802.11b  ESSID:"WDS"
          Mode:Repeater  Frequency:2.462GHz  Access Point: 00:00:00:00:00:00
          Bit Rate=2Mb/s   Tx-Power=24 dBm   Sensitivity=1/3
          Retry min limit:8   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

wlan0wds  IEEE 802.11b  ESSID:"WDS"
          Mode:Repeater  Frequency:2.462GHz  Access Point: 00:00:00:00:00:00
          Bit Rate=2Mb/s   Tx-Power=24 dBm   Sensitivity=1/3
          Retry min limit:8   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off

and my startup settings for WDS1:

mode=repeater
channel=11
essid=WDS
txpower=200mW
sens=1
other_ap_policy=0
max_wds=1
autom_ap_wds=0
wds_type=4
ap_auth_algs=1
txratectrl=0
beacon_int=100
dtim_period=10
pseudo_ibss=0
ap_max_inactivity=10
ap_bridge_packets=0
ap_nullfunc_ack=0
wds_neighbor=00:02:6F:01:FA:47
firmware=1.5.6:/etc/pcmcia/rf010506.hex








WDS2:

wlan0     IEEE 802.11b  ESSID:"WDS"
          Mode:Repeater  Frequency:2.462GHz  Access Point: 00:00:00:00:00:00
          Bit Rate:11Mb/s   Tx-Power=24 dBm   Sensitivity=1/3
          Retry min limit:8   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

wlan0wds  IEEE 802.11b  ESSID:"WDS"
          Mode:Repeater  Frequency:2.462GHz  Access Point: 00:00:00:00:00:00
          Bit Rate:11Mb/s   Tx-Power=24 dBm   Sensitivity=1/3
          Retry min limit:8   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off

and my startup settings for WDS2:

mode=repeater
channel=11
essid=WDS
txpower=200mW
sens=1
other_ap_policy=0
max_wds=1
autom_ap_wds=0
wds_type=4
ap_auth_algs=1
txratectrl=0
beacon_int=100
dtim_period=10
pseudo_ibss=0
ap_max_inactivity=10
ap_bridge_packets=0
ap_nullfunc_ack=0
wds_neighbor=00:02:6F:03:FE:E5
firmware=1.5.6:/etc/pcmcia/rf010506.hex

....
>
> And now I see Jouni hard at work with some new WDS fixes a few minutes
> ago...;)
>
> Off to try CVS now...
>
>
> -Dave
>
> _______________________________________________
> HostAP mailing list
> HostAP at shmoo.com
> http://lists.shmoo.com/mailman/listinfo/hostap
>