installing hostap

msc1 at alu.um.es msc1 at alu.um.es
Wed Nov 20 13:05:20 EST 2002


Hello, I have an AMD K6-2 with Red Hat 7.2, an AVAYA wireless card, and 
hostap-2002-10-12. The driver compile and starts, and I can put my computer in 
master mode, but show this:

------------------------------------------------------------
Could not read current WEP flags.
wlan0: encryption setup failed
wlan0: prism2_close
wlan0: Deauthenticate all stations
Could not read current WEP flags.
wlan0: encryption setup failed
prism2_detach
hostap_cs: detach postponed, 'wlan0' still locked
prism2_release
release - done
hostap_cs: Netdevice wlan0 unregistered
hostap_cs: Driver unloaded
Trying to free nonexistent resource <000003e0-000003e1>
unloading Kernel Card Services
Linux Kernel Card Services 3.1.22
  options:  [pci] [cardbus] [pm]
Intel PCIC probe: 
  VIA VT83C469 ISA-to-PCMCIA at port 0x3e0 ofs 0x00, 2 sockets
    host opts [0]: [ring]
    host opts [1]: [ring]
    ISA irqs (default) = 3,7,9,11,12 polling interval = 1000 ms
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x378-0x37f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0x0d0000-0x0dffff: clean.
hostap_cs: hostap_cs.c 0.0.0 2002-10-12 (SSH Communications Security Corp, 
Jouni Malinen)
hostap_cs: (c) Jouni Malinen <jkmaline at cc.hut.fi>
hostap_cs: setting Vcc=33 (constant)
hostap_cs: CS_EVENT_CARD_INSERTION
prism2_config()
hostap_cs: setting Vcc=50 (from config)
Checking CFTABLE_ENTRY 0x01 (default 0x01)
IO window settings: cfg->io.nwin=1 dflt.io.nwin=1
io->flags = 0x0046, io.base=0x0000, len=64
hostap_cs: index 0x01: Vcc 5.0, irq 3, io 0x0100-0x013f
hostap_cs: Registered netdevice wlan0
prism2_hw_init()
prism2_hw_config: initialized in 3523 iterations
wlan0: NIC: id=0x01 v4.2.1
wlan0: PRI: id=0x15 v4.4.1
wlan0: STA: id=0x1f v6.16.1
wlan0: CMD=0x0121 => res=0x7f, resp0=0x0004
wlan0: hfa384x_set_rid: CMDCODE_ACCESS_WRITE failed (res=127, rid=fc33, len=2)
wlan0: Beacon interval setting to 100 failed
wlan0: CMD=0x0121 => res=0x7f, resp0=0x0004
wlan0: hfa384x_set_rid: CMDCODE_ACCESS_WRITE failed (res=127, rid=fcb3, len=2)
wlan0: Basic rates setting failed
wlan0: CMD=0x0121 => res=0x7f, resp0=0x0004
wlan0: hfa384x_set_rid: CMDCODE_ACCESS_WRITE failed (res=127, rid=fcb4, len=2)
wlan0: Supported rates setting failed
wlan0: CMD=0x0121 => res=0x7f, resp0=0x0004
wlan0: hfa384x_set_rid: CMDCODE_ACCESS_WRITE failed (res=127, rid=fc10, len=2)
wlan0: DTIM period setting to 1 failed
Could not read current WEP flags.
wlan0: encryption setup failed
wlan0: could not configure encryption
wlan0: LinkStatus=2 (Disconnected)
wlan0: LinkStatus=1 (Connected)
prism2: wlan0: operating mode changed 3 -> 1
wlan0: LinkStatus=2 (Disconnected)
wlan0: LinkStatus: BSSID=02:02:2d:2b:bb:21
wlan0: LinkStatus=2 (Disconnected)
wlan0: LinkStatus: BSSID=44:44:44:44:44:44
Could not read current WEP flags.
wlan0: encryption setup failed
set_encryption or reset_port failed
wlan0: LinkStatus=2 (Disconnected)
wlan0: LinkStatus: BSSID=44:44:44:44:44:44
wlan0: LinkStatus=1 (Connected)
wlan0: LinkStatus: BSSID=02:02:2d:2b:bb:21
CNFWEPFLAGS reading failed
prism2: wlan0: operating mode changed 1 -> 3
wlan0: LinkStatus=2 (Disconnected)
wlan0: LinkStatus=2 (Disconnected)
wlan0: LinkStatus=2 (Disconnected)
Could not read current WEP flags.
wlan0: encryption setup failed
set_encryption or reset_port failed
wlan0: LinkStatus=2 (Disconnected)
wlan0: prism2_open
wlan0: LinkStatus=1 (Connected)
wlan0: Could not find STA for this TX error
wlan0: Could not find STA for this TX error
Could not read current WEP flags.
wlan0: encryption setup failed
wlan0: LinkStatus=1 (Connected)
wlan0: LinkStatus=1 (Connected)
--------------------------------------------------------

and other wireless devices not detect it as an access point. Other devices 
detect it as peer to peer connection.

Also have a D-LINK DWL-650 wireless card, but the driver not start with that 
card.

Please, help me.





More information about the HostAP mailing list